Back support shall be 2½ inches (64 mm) maximum from the rear edge of the seat measured horizontally. [2010 ADA Standards] 903.4 Back Support....
Search Results "Horizontal Position"
Filters
Commonly Searched Documents
-
11B-903.4 Back support
-
Footrests and Armrests: ADA Standard Section 1009.2.6
If provided, the armrest positioned opposite the water shall be removable or shall fold clear of the seat when the seat is in the raised (load) position....
-
Exit Doors: ADA Standard Section 216.4.1
Section 216.4.1 covers scoping requirements in the current ADA Standards for signs at exit doors.
-
1009.6.4 Separation
Each area of refuge shall be separated from the remainder of the story by a smoke barrier complying with Section 709 or a horizontal exit complying with Section 1026....
-
1009.3.2 Stairway width
The clear width of 48 inches (1219 mm) between handrails is not required for stairways accessed from a refuge area in conjunction with a horizontal exit....
-
2. Standing Supports
The proposed rule provided technical criteria for vertical and horizontal standing supports....
-
PLATFORM
entertainment; the head table for special guests; the raised area for lecturers and speakers; boxing and wrestling rings; theater-in-the-round stages; and similar purposes wherein, other than horizontal...
-
903 Benches
The proposed rule specified that the wheelchair space be positioned so that it provides a parallel approach to an end of the bench seat (903.2)....
-
Re: American Specialties 9014 Surface Mounted Horizontal Baby Changing Station
Rejected this after installation. The design of the hand hold is completely sloped at about 45 degrees. My fingers slipped off unless I applied tremendous pinching force to operate....
-
11B-806.2.3 Sleeping areas
The clear space shall be positioned for parallel approach to the side of the bed. [2010 ADA Standards] 806.2.3 Sleeping Areas....
-
11B-703.8.4 Character height
Viewing distance shall be measured as the horizontal distance between the character and an obstruction preventing further approach towards the sign....
-
Door and Gate Surfaces: ADA Standard Section 404.2.10
Section 404.2.10 covers the current ADA Standards for door and gate surfaces on manual doors and gates.
-
11B-608.3 Grab bars
Where multiple grab bars are used, required horizontal grab bars shall be installed at the same height above the finish floor....
-
11B-404.2.10 Door and gate surfaces
Parts creating horizontal or vertical joints in these surfaces shall be within 1/16 inch (1.6 mm) of the same plane as the other and be free of sharp or abrasive edges....
-
4.3.2 Transfer Surfaces and Imaging Equipment Functions
In DXA, the X-ray source is positioned under the patient in a fixed, known geometry; this positioning maximizes diagnostic effectiveness and minimizes radiation doses (see below)....
-
RECOMMENDED CHANGE
It specifies loading as percentage of patient weight (50% vertical and 25% horizontal)....
-
§ 37.42(f)
(f) For purposes of this part, level-entry boarding means a boarding platform design in which the horizontal gap between a car at rest and the platform is no more than 10 inches on tangent...
-
§ 37.42(f)
(f) For purposes of this part, level-entry boarding means a boarding platform design in which the horizontal gap between a car at rest and the platform is no more than 10 inches on tangent...
-
11B-216.4.1 Exit doors
An exit passageway is a horizontal exit component that is separated from the interior spaces of the building by fire-resistance-rated construction and that leads to the exit discharge or...
-
11B-703.7.2.7 Pedestrian traffic-control buttons
Pole-supported pedestrian traffic-control buttons shall be identified with color coding consisting of a textured horizontal yellow band 2 inches (51 mm) in width encircling the pole, and...
-
4.3.7 Clear Floor Space for Reaching
These dimensions are: (A) occupied width, the horizontal distance between the side-most (lateral-most) points of the wheelchair or occupant on the right and left side; (B) occupied length...
-
11B-803.6 Mirrors
Mirrors shall be full length with a reflective surface 18 inches (457 mm) wide minimum by 54 inches (1372 mm) high minimum and shall be mounted in a position affording a view to a person...
-
Adjustable height/gap protocol
This procedure was repeated until the largest horizontal distance was reached. The maximum and minimum heights attainable with the largest horizontal distance were recorded. ...
-
Sleeping Areas: ADA Standard Section 806.2.3
The clear floor space shall be positioned for parallel approach to the side of the bed....