The landing clear length shall be 48 inches (1219 mm) minimum....
Search Results "Full Length Mirror"
-
11B-406.5.3 Landings
-
§382.133(e)(2)
(2) The maximum weight and dimensions (length, width, height) of the device to be used by an individual that can be accommodated in the aircraft cabin consistent with FAA safety requirements...
-
§ 38.29(c)
(c) For vehicles in excess of 22 feet in length, overhead handrail(s) shall be provided which shall be continuous except for a gap at the rear doorway....
-
Boarding Pier Clearances
Boarding Pier Clearances The entire length of accessible boarding piers must comply with the same technical provisions that apply to boat slips....
-
Unified Facilities Guide Specifications
The straightedge is to be held in contact with the surface and moved ahead one - half of the length of the straightedge for each successive measurement....
-
225(d)(1)(E)
(E) prohibit relay operators from failing to fulfill the obligations of common carriers by refusing calls or limiting the length of calls that use telecommunications relay services;...
-
11B-813.2.1.1 Size
Adult changing tables shall have a changing surface of 70 inches (1778 mm) minimum length and 30 inches (762 mm) minimum width....
-
505.6 Gripping Surface
Handrail gripping surfaces shall be continuous along their length and shall not be obstructed along their tops or sides....
-
505.6 Gripping Surface
Handrail gripping surfaces shall be continuous along their length and shall not be obstructed along their tops or sides....
-
11B-505.6 Gripping surface
Handrail gripping surfaces shall be continuous along their length and shall not be obstructed along their tops or sides....
-
7.4.3.1 Running Slope (Grade)
No more than 30 percent of the total trail length may exceed a running slope (grade) of 1:12 (8.33 percent)....
-
Pilot Rock WXT and WXTH Picnic Table Using Aluminum
Full length seats offer full capacity seating which is an advantage over extended top or side access tables. ...
-
Pilot Rock WUT and WUTH Picnic Table - Using Aluminum
Full length seats offer full capacity seating which is an advantage over extended top or side access tables. ...
-
Bobrick Recessed Paper Towel Dispenser B-318
Towels load into bottom of cabinet concealed behind wall or mirror; only the towel tray is visible....
-
106.5.66 Structural Impracticability
In new construction, full compliance with the requirements of these standards is not required where an entity can demonstrate that it is structurally impracticable to meet the requirements...
-
III-4.4300 Standards to apply
Deviations from ADAAG are acceptable only when full compliance with those requirements is not readily achievable....
-
Using the Tape Measure
A tape measure is used to measure the length, width, height, and depth of various elements including parking spaces and access aisles, routes, thresholds, doorways, and protruding objects...
-
§382.133(f)(3)
(3) The maximum weight and dimensions (length, width, height) of the device to be used by an individual that can be accommodated in the aircraft cabin consistent with the safety regulations...
-
C1-3. Accessible Route Width
If No, the accessible route may narrow to 32 inches wide for up to 2 feet in length. Yes _____ No _____...
-
Conclusions
A depth of 15in. for a seating surface was found to be suitable based on median values of buttock-popliteal length and wheelchair seat depths....
-
1017.4 Passing Spaces
Where the full length of a trail does not fully comply with the technical requirements in 1017, a passing space is required to be located at the end of the trail segment that fully complies...
-
11B-1003.2.2 Boarding piers at boat launch ramps
Where the total length of the gangway or series of gangways serving as part of a required accessible route is 30 feet (9144 mm) minimum, gangways shall not be required to comply with Section...
-
11B-1003.2.2 Boarding piers at boat launch ramps
Where the total length of the gangway or series of gangways serving as part of a required accessible route is 30 feet (9144 mm) minimum, gangways shall not be required to comply with Section...
-
1017.8 Resting Intervals
This section contains the technical requirements for the length (1017.8.1), width (1017.8.2), and slope (1017.8.3) of resting intervals; and for a turning space (1017.8.4) where resting...
