In standard roll-in type shower compartments, the controls, faucets, and the shower spray unit shall be located on the back wall of the compartment adjacent to the seat 16 inches (406 mm...
Search Results "Back Support"
-
11B-608.5.2 Standard roll-in type shower compartments
-
11B-502.3.4 Location
Many drivers, especially those who operate vans, find it more difficult to back into parking spaces than to back out into comparatively unrestricted vehicular lanes....
-
§ 38.23(c)(1) Design load
Ramps 30 inches or longer shall support a load of 600 pounds, placed at the centroid of the ramp distributed over an area of 26 inches by 26 inches, with a safety factor of at least 3 based...
-
12. Is an agency required to arrange for services to parents and prospective parents with disabilities that are necessary to avoid discrimination but are not available within the agency’s programs?
Many specialized services to support persons with disabilities are often available from other social service agencies, as well as disability organizations. ...
-
Comments on the Three Options
Supporters stated that the Option One guidelines provided a faithful and clearly stated interpretation of the Act's intent....
-
H21
Is a horizontal grab bar at least 40 inches long securely mounted on the adjacent side wall 33 to 36 inches above the floor with one end no more than 12 inches from the back wall 33 to 36...
-
11B-605.2 Height and depth
Urinals shall be 131/2 inches (343 mm) deep minimum measured from the outer face of the urinal rim to the back of the fixture....
-
Service Animal:
With respect to emotional support animals, although carriers may require documentation to verify that an animal is an emotional support animal, such documentation is not required under the...
-
§ 38.83(c)(1) Design load
Ramps or bridge plates 30 inches or longer shall support a load of 600 pounds, placed at the centroid of the ramp or bridge plate distributed over an area of 26 inches, with a safety factor...
-
11B-605.2 Height and depth
Urinals shall be 13½ inches (343 mm) deep minimum measured from the outer face of the urinal rim to the back of the fixture. FIGURE 11B-605.2 HEIGHT AND DEPTH OF URINALS...
-
14) Carpet and carpet tile
Carpet tile must have maximum combined thickness of pile, cushion, and backing height of 1/2" (§4.5.3)....
-
General: ADA Standard Section 306.1
Section 306.1 of the ADA Standards covers information in the current ADA Standards for knee and toe clearance.
-
Cybex Total Access Chest Press Exercise Machine
Adjustable Input Arm Enables a non-stressed start position for users with limited shoulder flexibility and wheelchair users Upright Seat Back Support Upright seat back support (...
-
Pilot Rock LDW-36/18 Campfire Ring
The 3/16” thick steel panels support the cooking grate in 4 locations and help shield the grate handles from heat. ...
-
605.2 Height and Depth
Urinals shall be 13½ inches (345 mm) deep minimum measured from the outer face of the urinal rim to the back of the fixture. Figure 605.2 Height and Depth of Urinals...
-
605.2 Height and Depth
Urinals shall be 13½ inches (345 mm) deep minimum measured from the outer face of the urinal rim to the back of the fixture....
-
7.4.11.1 Clear Space
Trailhead signs shall be located centered at the back of a 30- by 48-inch (760- by 1,220-millimeter) minimum clear floor or ground space....
-
§ 38.113(d)(3) Exception
Where platform set-backs do not allow the horizontal gap or vertical alignment specified in paragraph (d) (1) or (2), platform or portable lifts complying with §38.125(b) of this part, or...
-
7. What remedies address violations of the ADA’s integration mandate in the context of disability employment systems?
The Department has entered into settlement agreements that require states to expand the services and supports available in integrated employment settings....
-
C201.1 Scope
Manufacturers shall also conform to the requirements in the Revised 255 Guidelines for support documentation and services, including electronic documents and Web-based product support....
-
§ 38.125(c)(1) Design load
Ramps or bridge plates 30 inches or longer shall support a load of 600 pounds, placed at the centroid of the ramp or bridge plate distributed over an area of 26 inches by 26 inches, with...
-
§ 38.95(c)(1) Design load
Ramps or bridge plates 30 inches or longer shall support a load of 600 pounds, placed at the centroid of the ramp or bridge plate distributed over an area of 26 inches by 26 inches, with...
-
11B-802.1.3 Depth
A single wheelchair location space with side entry must functionally be usable as if it were within an alcove, requiring the user to maneuver back and forth to get into position, and thus...
-
Section 1630.15(f) Claims Based on Transitory and Minor Impairments Under the “Regarded As” Prong
For example, an individual who is denied a promotion because he has a minor back injury would be “regarded as” an individual with a disability if the back impairment lasted or was expected...
