(1) Airports must consult with one or more service animal training organizations regarding the design, dimensions, materials and maintenance of service animal relief areas;...
Search Results "Maximum Dimension"
Filters
Commonly Searched Documents
-
§27.71(h)(1)
-
5.8.2.4 Unobstructed Floor Space Recommendation
The pose reduces the abdomen-toe and abdomen-caster edge dimensions by a couple of inches....
-
5.2.3 Transfer Surface Measurement Recommendation for M301 and M302
The transfer surface dimensions do not include headrests, footrests, or similar supports for body extremities that do not support the patient’s overall body position....
-
11B-303.2 Vertical
Changes in level of ¼ inch (6.4 mm) high maximum shall be permitted to be vertical and without edge treatment. [2010 ADA Standards] 303.2 Vertical....
-
407.2.1.2 Size
Call buttons shall be 3/4 inch (19 mm) minimum in the smallest dimension. EXCEPTION: Existing elevator call buttons shall not be required to comply with 407.2.1.2....
-
5. Curb Ramp Running Slope
5. ...do the curb ramps have running slopes of 1:12 or less (critical dimension of 2" or less)?...
-
7. Exterior Ramp Running Slope
7. ...do the exterior ramps have running slopes of 1:12 or less (critical dimension of 2" or less)?...
-
407.2.1.2 Size
Call buttons shall be ¾ inch (19 mm) minimum in the smallest dimension. EXCEPTION: Existing elevator call buttons shall not be required to comply with 407.2.1.2....
-
Figures in the Standards
Figures in the ADA Standards are provided only for informational purposes to illustrate dimensions and requirements contained in the text....
-
Mayer-Rothschild Foundation: Determination of Grab Bar Specifications for Independent and Assisted Transfers in Residential Care Settings
The purpose of this project is to identify, both objectively and subjectively, the spatial and configurational dimensions of grab-bars that effectively support both independent standing...
-
Dispensers: ADA Standard Section 604.7
Section 604.7 covers the current ADA Standards for toilet paper dispensers.
-
5.8.2.8 Knee and Toe Clearance Recommendations Summary
For such a measurement, the top of the breast platform will be moved to 34 inches above the ground, and then the clearance dimensions will be measured just as they would be on any stationary...
-
Parking
PARKING Location and number of van parking and standard parking spaces. 11B-208 Dimensions of accessible parking spaces and access...
-
Parking
PARKING Location and number of van parking and standard parking spaces. 11B-208 Dimensions of accessible parking spaces and access...
-
11B-608.2.2 Standard roll-in type shower compartments
Standard roll-in type shower compartments shall be 30 inches (762 mm) wide minimum by 60 inches (1524 mm) deep minimum clear inside dimensions measured at center points of opposing sides...
-
11B-608.9 Shower floor or ground surface
Floor or ground surfaces of showers shall comply with Section 11B-302.1 and shall be sloped 1:48 maximum in any direction....
-
803 Dressing, Fitting, and Locker Rooms
In the proposed rule, an exception to this provision noted that a portion of this space (6 inches maximum) could extend under partitions or openings without doors that provide toe clearance...
-
1115B.4.4.8, Item 1
A folding seat mounted 18 inches (457 mm) above the floor, and with a minimum space of 1 inch (25 mm) and maximum space of 1 1/2 inches (38 mm) allowed between the edge of the seat and any...
-
11B-703.7.2.6.4 Edges and vertices on geometric symbols
Edges shall be eased or rounded at 1/16 inch (1.59 mm) minimum, or chamfered at 1/8 inch (3.2 mm) maximum....
-
Technical requirements
Technical requirements state the specific numbers, conditions, and measurements that are required (percent that must comply, dimensions, reach ranges, grades, trail width, and so forth)....
-
§ 38.4(b) Dimensional tolerances
All dimensions are subject to conventional engineering tolerances for material properties and field conditions, including normal anticipated wear not exceeding accepted industry-wide standards...
-
Water Flow: ADA Standard Section 602.6
Section 602.6 covers the current ADA Standards for the drinking fountain water flow.
-
M305.3 Standing Supports (Section-by-Section Analysis)
In the MDE NPRM preamble, the Access Board noted that it was considering adopting the cross section dimensions for grab bars from the 2004 ADA and ABA Accessibility Guidelines and applying...
-
Counter: ADA Standard Section 904.3.2
The counter surface height shall be 38 inches (965 mm) maximum above the finish floor or ground....
