Work surfaces shall be 36 inches (914 mm) maximum above the finish floor with minimum lengths at the following locations as required by this section: Linear length of 30 inches...
Search Results "End Transfer Surface"
Filters
Commonly Searched Documents
-
11B-809.9.4 Work surfaces
-
Cross Slope and Surfaces [4.8.6]
Ramp surfaces must comply with requirements for ground and floor surfaces and be "stable, firm, and slip-resistant." A specific level of slip-resistance is not mandated....
-
Grab bars
Grab bars: Section 609 of the ADA-ABA standards [7] includes provisions for grab bars in areas where transfers are expected....
-
Accessible Exterior Surfaces
Accessible Exterior Surfaces This is an executive summary of the “Accessible Exterior Surfaces Technical Report” dated 24 April 1999....
-
Pilot Rock UT and UTH Series End Accessible Aluminum Picnic Table
LENGTH: 6 ft. seats with 8 ft. top (extended on one end); 6 ft. seats with 10 ft top (extended on both ends); 8 ft. seats with 10 ft. top (extended on...
-
KICK PLATE
An abrasion-resistant plate affixed to the bottom portion of a door to prevent a trap condition and protect its surface. Advisory Definition of KICK PLATE....
-
11B-1008.2.4.2 Elevated
The clear width of transfer systems connecting elevated play components shall be permitted to be 24 inches (610 mm) minimum....
-
4.10.10 Floor Surfaces
Floor surfaces shall comply with 4.5....
-
4.10.10 FLOOR SURFACES
Floor surfaces shall comply with 4.5....
-
5.4.3 Transfer Support Height for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
5.4.3 Transfer Support Height for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position....
-
407.4.2 Floor Surfaces
Floor surfaces in elevator cars shall comply with 302 and 303....
-
407.4.2 Floor Surfaces
Floor surfaces in elevator cars shall comply with 302 and 303....
-
§ 35.138(f) Ticket transfer
(f) Ticket transfer....
-
Elevated: ADA Standard Section 1008.2.4.2
The clear width of transfer systems connecting elevated play components shall be permitted to be 24 inches (610 mm) minimum....
-
R407.9.1 Extended Ramp Surface
R407.9.1 Extended Ramp Surface. The surface of the ramp run or landing shall extend 305 mm (1.0 ft) minimum beyond the inside face of a handrail complying with R409....
-
General: ADA Standard Section 403.1
Section 403.1 of the ADA Standards covers information in the current ADA Standards for walking surfaces that are part of an accessible route.
-
Pilot Rock XT and XTH Series End Accessible Picnic Table Using Aluminum
LENGTH: 6 ft. seats with 8 ft. top (extended on one end); 6 ft. seats with 10 ft top (extended on both ends); 8 ft. seats with 10 ft. top (extended on...
-
Pilot Rock UT and UTH Series End Accessible Picnic Table Using Lumber
LENGTH: 6 ft. seats with 8 ft. top (extended on one end); 6 ft. seats with 10 ft top (extended on both ends); 8 ft. seats with 10 ft. top (extended on...
-
504.4 Tread Surface
504.4 Tread Surface. Stair treads shall comply with 302. Changes in level are not permitted. EXCEPTION: Treads shall be permitted to have a slope not steeper than 1:48....
-
11B-403.1 General
Walking surfaces that are a part of an accessible route shall comply with Section 11B-403....
-
Backrests
Backrests: The backrest design for platform 1, the first surface that participants transferred to from their WMD as seen in Table 2, was based on bench seat back supports in section 903.5...
-
6.5 Surface
The surface of beach access routes and their related resting intervals shall be firm and stable....
-
11B-404.2.4.4 Floor or ground surface
Floor or ground surface within required maneuvering clearances shall comply with Section 11B-302. Changes in level are not permitted. Exceptions: 1. ...
-
11B-404.2.4.4 Floor or ground surface
Floor or ground surface within required maneuvering clearances shall comply with Section 11B-302. Changes in level are not permitted. Exceptions: 1....
