Transfer supports and surfaces adjacent to transfer supports shall be free of sharp or abrasive components and shall have eased edges....
Search Results "End Transfer Surface"
-
M305.2.5 Surface Hazards
-
608.2.1 Transfer Type Shower Compartments
Transfer type shower compartments shall be 36 inches (915 mm) by 36 inches (915 mm) clear inside dimensions measured at the center points of opposing sides and shall have a 36 inch (915...
-
Bonded Impact/cushioning Surfaces
Bonded Impact/cushioning Surfaces Eight different surface test specimens were formed with surface dimensions of 1.2m x 1.2m with a depth of 0.3m (48”x48”x 12”) in Madison WI (Figure 1...
-
11B-1002.6 Transfer devices for use with amusement rides
When using a transfer device to access an amusement ride, the least number of transfers and the shortest distance is most usable....
-
11B-1002.6 Transfer devices for use with amusement rides
When using a transfer device to access an amusement ride, the least number of transfers and the shortest distance is most usable....
-
11B-1002.6 Transfer devices for use with amusement rides
When using a transfer device to access an amusement ride, the least number of transfers and the shortest distance is most usable....
-
Handrails: ADA Standard Section 403.6
Section 403.5.4 covers the current ADA Standards for handrails that are provided along walking surfaces of accessible routes.
-
Firmness or Firm Surface
Firmness or Firm Surface. A firm surface resists deformation by either indentations or particles moving on its surface (2010 ADA Standards for Accessible Design, Advisory 302.1). ...
-
1018.3 Surface
The surface of beach access routes and resting intervals shall be firm and stable....
-
1018.3 Surface
The surface of beach access routes and resting intervals shall be firm and stable....
-
810.2.1 Surface
Bus stop boarding and alighting areas shall have a firm, stable surface....
-
1018.3 Surface
This section requires the surface of beach access routes and resting intervals to be firm and stable....
-
810.2.1 Surface
Bus stop boarding and alighting areas shall have a firm, stable surface....
-
5.4.3 Transfer Support Height for M301 and M302
5.4.3 Transfer Support Height for M301 and M302 Description: Transfer support height applies to the vertical distance that the gripping area of the support is above the transfer surface...
-
Ramp
Ramp: A ramped surface was designed to insert between two steps and serve as an integrated sliding board to assist with the transfers by bridging the gap between steps. ...
-
11B-403.6 Handrails
Where handrails are provided along walking surfaces with running slopes not steeper than 1:20 they shall comply with Section 11B-505. Advisory 11B-403.6 Handrails....
-
11B-403.6 Handrails
Where handrails are provided along walking surfaces with running slopes not steeper than 1:20 they shall comply with Section 11B-505. Advisory 11B-403.6 Handrails....
-
Initial Measures and Transfer Setup
However, for the setup of the baseline level transfer (when the person and mobility device were in a position next to platform ready to transfer), if there was a noticeable difference (one...
-
Entry Points and Seats: ADA Standard Section 1008.4.4
Where play components require transfer to entry points or seats, the entry points or seats shall be 11 inches (280 mm) minimum and 24 inches (610 mm) maximum from the clear floor or ground...
-
11B-1002.4.1 Floor or ground surface
The floor or ground surface of wheelchair spaces shall be stable and firm....
-
11B-1002.4.1 Floor or ground surface
The floor or ground surface of wheelchair spaces shall be stable and firm....
-
11B-1002.4.1 Floor or ground surface
The floor or ground surface of wheelchair spaces shall be stable and firm....
-
Ticket transfer. (Section-by-Section Analysis)
Ticket transfer. The Department received many comments asking whether accessible seating has the same transfer rights as general seats....
-
5.3 Transfer Sides
5.3 Transfer Sides....