Surfaces of transfer walls shall not be sharp and shall have rounded edges....
Search Results "Edge Protection"
-
1009.4.4 Surface
-
405 Ramps
Technical provisions address running slope, cross slope, handrails, landings, edge protection, and other elements....
-
FIGURE INDEX
Maneuvering Clearances at Recessed Doors and Gates Figure 404.2.6 Doors in Series and Gates in Series Figure 405.7 Ramp Landings Figure 405.9.1 Extended Floor or Ground Surface Edge...
-
Transfer Sides (M301.2.3 and M302.2.3)
Otherwise, no part of the equipment can project beyond the edge of the transfer sides and obstruct access to the transfer surface....
-
Haws Barrier-Free Chilled Dual Wall Mount Fountain H1011.8HO
Outfitted with such protective features as vandal resistant bubbler heads, waste strainer, and bottom plates, these electric water coolers are quick to discourage vandals. 18 gauge...
-
AJW Architectural Products US888 Single Security Toilet Tissue Dispenser, Exposed Mounting - Surface Mounted - Non-Controlled
Theft Unit is designed for security applications Product Specs Body: Fabricated of #18 ga. stainless steel, one piece construction with a #4 satin finish with a removable vinyl protective...
-
BEA Inc. Jamb Style Door Access PTE (Push To Exit)
rusting Stainless steel materials are 100% recyclable and environmentally friendly Available in hard wired and wireless options (433, 390 or 300 MHz) Beveled edges...
-
11B-705.1.2.3 Islands or cut-through medians
cut-through medians shall be 36 inches (914 mm) minimum in depth extending the full width of the pedestrian path or cut-through less 2 inches (51 mm) maximum on each side, placed at the edges...
-
Back Support: ADA Standard Section 903.4
Back support shall be 2½ inches (64 mm) maximum from the rear edge of the seat measured horizontally. Advisory 903.4 Back Support....
-
11B-705.1.2.3 Islands or cut-through medians
cut-through medians shall be 36 inches (914 mm) minimum in depth extending the full width of the pedestrian path or cut-through less 2 inches (51 mm) maximum on each side, placed at the edges...
-
General [5.1]/ Access Aisles [5.3]
The required clear width (36 inches minimum) is specified for the clearance between the edges of fixed tables or between table edges and walls....
-
§ 38.83(b)(7) Platform gaps
When the lift is at vehicle floor height with the inner barrier (if applicable) down or retracted, gaps between the forward lift platform edge and vehicle floor shall not exceed 1/2 inch...
-
Surface
Surface The surface of the transfer platform and steps must not be sharp and must have rounded edges to prevent injuries....
-
1117B.1, Item 5
The bubbler outlet orifice shall be located within 6 inches (152mm) of the front edge of the drinking fountain and within 36 inches (914 mm) of the floor....
-
1117B.1, Item 4
The bubbler outlet orifice shall be located within 6 inches (152mm) of the front edge of the drinking fountain and within 36 inches (914 mm) of the floor....
-
§382.45(b)(4)
(4) On the Aviation Consumer Protection Division's Web site (http://airconsumer.ost.dot.gov)....
-
4.7.8 Obstructions
Curb ramps shall be located or protected to prevent their obstruction by parked vehicles....
-
4.7.8 OBSTRUCTIONS
Curb ramps shall be located or protected to prevent their obstruction by parked vehicles....
-
Guest Bathrooms
Permanent seats at the head end of the bathtub shall be 15 inches (380 mm) deep minimum and shall extend from the back wall to or beyond the outer edge of the bathtub. 610.3 Shower...
-
1009.4.2 Area of refuge
Areas of refuge are not required at elevators serving smoke-protected or open-air assembly seating areas complying with Sections 1029.6.2 and 1029.6.3....
-
11B-409.4.3 Platform to hoistway clearance
The clearance between the car platform and the edge of any landing sill shall be 1½ inch (38 mm) maximum....
-
11B-410.4 Platform to runway clearance
The clearance between the platform sill and the edge of any runway landing shall be 1¼ inch (32 mm) maximum....
-
410.4 Platform to Runway Clearance
The clearance between the platform sill and the edge of any runway landing shall be 1 inch (32 mm) maximum....
-
409.4.3 Platform to Hoistway Clearance
The clearance between the car platform and the edge of any landing sill shall be 1-½ inch (38 mm) maximum....
