Section 203.8 of the 2010 Standards provides that, in residential facilities, common use areas that do not serve residential dwelling units required to provide mobility features are not...
Search Results "Mobility Feature"
Filters
Commonly Searched Documents
-
Common Use Areas in Residential Facilities—Section 203.8 of the 2010 Standards
-
1017.3 Clear Tread Width
The research is known as the Anthropometry of Wheeled Mobility Project and was conducted by the Center for Inclusive Design and Environmental Access in the School of Architecture and Planning...
-
Visible Alarms in Guest Rooms with Communication Features
Visible Alarms in Guest Rooms with Communication Features....
-
The Accessibility Management Platform (AMP) - AMP for Mobile
Mobile Accessibility: There's an App for That!...
-
§ 38.125(d)(2) Wheelchair or mobility aid spaces
(2) Wheelchair or mobility aid spaces. Spaces for persons who wish to remain in their wheelchairs or mobility aids shall have a minimum clear floor space 48 inches by 30 inches....
-
III-3.7000 Maintenance of accessible features
III−3.7000 Maintenance of accessible features....
-
233.3.1.2 Facilities Containing Emergency Transportable Housing Units, F233.3.1.2 Facilities Containing Emergency Transportable Housing Units, F233.4.1.2 Facilities Containing Emergency Transportable Housing Units
F233.4.1.2 Facilities Containing Emergency Transportable Housing Units These sections contain the scoping requirements for emergency transportable housing units with communication features...
-
11B-701.1 Scope
The provisions of Division 7 shall apply where required by Division 2 or where referenced by a requirement in this chapter.
-
701.1 Scope
The provisions of Chapter 7 shall apply where required by Chapter 2 or where referenced by a requirement in this document.
-
701.1 Scope
The provisions of Chapter 7 shall apply where required by Chapter 2 or where referenced by a requirement in this document.
-
4. Amend § 35.133 by adding paragraph (c) to read as follows:
4. Amend § 35.133 by adding paragraph (c) to read as follows:
-
§ 35.133(c)
(c) If the proposed standards reduce the number of required accessible elements below the number required by the 1991 Standards, the number of accessible elements in a facility...
-
701.1 Scope
701.1 Scope. The provisions of Chapter 7 shall apply where required by Chapter 2 or where referenced by a requirement in this code.
-
MISCELLANEOUS PROVISIONS
Except as otherwise specified in this Agreement, at yearly anniversaries of the effective date of this Agreement until it expires, the City will submit written reports to the...
-
11B-701.1 Scope
11B-701.1 Scope. The provisions of Division 7 shall apply where required by Division 2 or where referenced by a requirement in this chapter.
-
11B-701.1 Scope
The provisions of Division 7 shall apply where required by Division 2 or where referenced by a requirement in this chapter.
-
WAY FINDING
[See subsections ...]
-
3.3.6 Knee Clearance Height, minimum
3.3.6 Knee Clearance Height, minimum Knee clearance heights for the four sets of standards range from 650 mm (25.6 in.) (Australia) to 700 mm (27.6 in.) (U.K.) (Figure 3‒6). The...
-
3.3.5 Seat Height
3.3.5 Seat Height Height dimension standards for seats prescribed in the Australian, Canadian and U.S. standards were very similar (480 mm or 18.9 in., 480 mm or 18.9 in. and 485...
-
3.3.8 Knee Clearance Depth, minimum
3.3.8 Knee Clearance Depth, minimum Knee clearance depths for the four sets of standards range from 200 mm (8 in.) in Canada to 280 mm (11 in.) in the U.S. (Figure 3‒8). None of...
-
Section 2.0 Methodology
2.0 Methodology
-
3.3.7 Toe Clearance Height, minimum
3.3.7 Toe Clearance Height, minimum There is relatively large disparity between the standards for toe clearance height, with the U.S. having the lowest (230 mm or 9 in.),...
-
2.3 Analysis
2.3 Analysis
-
Section 4.0 Implications for Standards and Design
Section 4.0 Implications for Standards and Design
