In the Table of Contents and Index of Figures, the underlines are omitted, for improved readability....
Search Results "Figures"
Filters
Commonly Searched Documents
-
Conventions used in this Pocket Guide
-
A4.17.3 Size and Arrangement
This section requires use of the 60 in (1525 mm) standard stall (Figure 30(a)) and permits the 36 in (915 mm) or 48 in (1220 mm) wide alternate stall (Figure 30(b)) only in alterations where...
-
Protruding Objects and Trails
Objects that extend into the travel way of a trail from the side or from overhead can be hazardous to people who are paying more attention to their companions than the travel route (figure...
-
3.3.5 Seat Height
The values in the current standards for seat height are below the means for people we measured and those in the UDI study (Figure 3‒5)....
-
3.3.15.1 Forward reach – unobstructed
percentage of WhMD users in our study could not reach beyond the most forward point of their WhMDs or foot, and the difference between users of different types of WhMDs was very large (Figure...
-
11B-201.1 Scope
Unless specifically stated otherwise, the advisory notes, appendix notes, and figures contained in the 1991 Standards and the Standards explain or illustrate the requirements of the rule...
-
707.6.2 Numeric Keys
Figure 707.6.2 Numeric Key Layout...
-
11B-1002.4.4.3 Permitted protrusions in wheelchair spaces
FIGURE 11B-1002.4.4.3 PROTRUSIONS IN WHEELCHAIR SPACES IN AMUSEMENT RIDES...
-
1002.4.4.3 Permitted Protrusions in Wheelchair Spaces
Figure 1002.4.4.3 Protrusions in Wheelchair Spaces in Amusement Rides...
-
11B-1009.3.2 Submerged depth
FIGURE 11B-1009.3.2 SLOPED ENTRY SUBMERGED DEPTH...
-
11B-304.3.2 T-Shaped space
FIGURE 11B-304.3.2 T-SHAPED TURNING SPACE...
-
608.2.1 Transfer Type Shower Compartments
Figure 608.2.1 Transfer Type Shower Compartment Size and Clearance ...
-
303.3 Beveled
Figure 303.3 Beveled Change in Level ...
-
604.2 Location
Figure 604.2 Water Closet Location...
-
405.7 Landings
Figure 405.7 Ramp Landings ...
-
304.3.2 T-Shaped Space
Figure 304.3.2 T-Shaped Turning Space...
-
Location of Controls
Comments indicated that this specification was not consistent with a corresponding figure showing the location on the side closest to the shower opening. Response....
-
5.2.2 Transfer Surface Size Recommendations for M302
(See Figure 5.2.1.1) NPRM Proposed Provision: M302.2.2 Size. The transfer surface shall be 21 inches wide minimum and 15 inches deep minimum....
-
610.2 Bathtub Seats
Figure 610.2 Bathtub Seats...
-
609.3 Spacing
Figure 609.3 Spacing of Grab Bars...
-
608.3.2 Standard Roll-In Type Shower Compartments
Figure 608.3.2 Grab Bars for Standard Roll-In Type Showers...
-
11B-610.2 Bathtub seats
FIGURE 11B-610.2 BATHTUB SEATS...
-
1009.3.2 Submerged Depth
Figure 1009.3.2 Sloped Entry Submerged Depth...
-
2. a. iv. Path-of-Travel (wheelchair) space allowances
If a 180° turn is needed to exit an area, then a 60” diameter turning space or a 36” wide "T" is needed (see Figure 11)....