Section 308.3.1 covers the current ADA Standards for unobstructed side reach.
Search Results "Expected Maximum Flight Duration"
Filters
Commonly Searched Documents
-
Unobstructed: ADA Standard Section 308.3.1
-
1.1.1
1.1.1 When a maximum or minimum dimension is a regulatory requirement use a drawing dimension that is less than a maximum limit or more than a minimum limit....
-
Technically Infeasible
With respect to an alteration of a building or a facility, something that has little likelihood of being accomplished because existing structural conditions would require removing or...
-
11B-104.1.1 Construction and manufacturing tolerances
Where a requirement is a minimum or a maximum dimension that does not have two specific minimum and maximum end points, tolerances may apply....
-
11B-104.1.1 Construction and manufacturing tolerances
Where a requirement is a minimum or a maximum dimension that does not have two specific minimum and maximum end points, tolerances may apply....
-
F209.2.3 On-Street Bus Stops
On-street bus stops shall comply with 810.2 to the maximum extent practicable....
-
209.2.3 On-Street Bus Stops
On-street bus stops shall comply with 810.2 to the maximum extent practicable....
-
11B-209.2.3 On-street bus stops
On-street bus stops shall comply with Section 11B-810.2 to the maximum extent practicable....
-
11B-209.2.3 On-street bus stops
On-street bus stops shall comply with Section 11B-810.2 to the maximum extent practicable....
-
11B-209.2.3 On-street bus stops
On-street bus stops shall comply with Section 11B-810.2 to the maximum extent practicable....
-
§ 36.402(c) To the maximum extent feasible.
(c) To the maximum extent feasible....
-
209.2.3 On-Street Bus Stops
On-street bus stops shall comply with 810.2 to the maximum extent practicable....
-
11B-104.1.1 Construction and manufacturing tolerances
Where a requirement is a minimum or a maximum dimension that does not have two specific minimum and maximum end points, tolerances may apply....
-
§ 37.43(b)
(b) As used in this section, the phrase to the maximum extent feasible applies to the occasional case where the nature of an existing facility makes it impossible to comply fully with applicable...
-
7.2.1 General Exception 1
Where a condition in 7.1 prohibits full compliance with a specific requirement in 7.4 on a trail segment, that trail segment shall comply with the specific requirement to the maximum extent...
-
11B-1002.4.7.1 Shoulder-to-shoulder seating
Exception: Where shoulder-to-shoulder companion seating is not operationally or structurally feasible, compliance with this requirement shall be required to the maximum extent practicable...
-
11B-1002.4.7.1 Shoulder-to-shoulder seating
Exception: Where shoulder-to-shoulder companion seating is not operationally or structurally feasible, compliance with this requirement shall be required to the maximum extent practicable...
-
F104.1.1 Construction and Manufacturing Tolerances
Where a requirement is a minimum or a maximum dimension that does not have two specific minimum and maximum end points, tolerances may apply....
-
104.1.1 Construction and Manufacturing Tolerances
Where a requirement is a minimum or a maximum dimension that does not have two specific minimum and maximum end points, tolerances may apply....
-
104.1.1 Construction and Manufacturing Tolerances
Where a requirement is a minimum or a maximum dimension that does not have two specific minimum and maximum end points, tolerances may apply....
-
Sec.36.402(c) To the maximum extent feasible
(c) To the maximum extent feasible....
-
308.3.2 Obstructed High Reach
and the depth of the obstruction shall be 24 inches (610 mm) maximum....
-
11B-1002.4.3 Gaps
at rest in the load and unload position, the vertical difference between the floors shall be within plus or minus 5/8 inches (15.9 mm) and the horizontal gap shall be 3 inches (76 mm) maximum...
-
11B-1002.4.3 Gaps
at rest in the load and unload position, the vertical difference between the floors shall be within plus or minus 5/8 inches (15.9 mm) and the horizontal gap shall be 3 inches (76 mm) maximum...