Search Results "Vertical Access"
-
Figure 610.2 Bathtub Seats – Drawing from the U.S. Access Board
-
Figure 306.3 Knee Clearance – Drawing from the U.S. Access Board
-
Figure 607.2 Clearance for Bathtubs – Drawing from the U.S. Access Board
-
Figure 1009.5.7 Grab Bars – Drawing from the U.S. Access Board
-
Figure 1009.5.4 Transfer Steps – Drawing from the U.S. Access Board
-
Stanley Access Technologies Dura-Care 7200 Manual Sliding Door
Requires the Premium User plan or above. (Login or upgrade your account!) -
Cybex Total Access Row/Rear Delt Exercise Machine Plan
Requires the Premium User plan or above. (Login or upgrade your account!) -
Cybex Total Access Seated Leg Curl Exercise Machine Plan
Requires the Premium User plan or above. (Login or upgrade your account!) -
1010.1.5 Floor elevation
Landings shall be level except for exterior landings, which are permitted to have a slope not to exceed 0.25 unit vertical in 12 units horizontal (2-percent slope)....
-
11B-504.5 Nosings
Risers shall be permitted to slope under the tread at an angle of 30 degrees maximum from vertical....
-
11B-504.5 Nosings
Risers shall be permitted to slope under the tread at an angle of 30 degrees maximum from vertical....
-
11B-504.5 Nosings
Risers shall be permitted to slope under the tread at an angle of 30 degrees maximum from vertical....
-
FAA Advisory Circular 150/5360-14: Access to Airport by Individuals with Disabilities
(Link to this document as a PDF online) Advisory Circular Subject: ACCESS TO AIRPORTS BY INDIVIDUALS WITH DISABILITIES Date: 6/30/99 Initiated by: AAS-100 AC No: 150/5360-14...
-
12. I am doing a small tenant improvement project, but I cannot afford the required accessibility improvements. Can I claim a hardship exemption?
‘Path-of-travel improvements’: Outside of the area of alteration, accessibility requirements must also be addressed....
-
QUESTION: WHAT ACCESSIBILITY STANDARDS APPLY TO PASSENGER RAIL CARS WHEN SPECIFIC DESIGN STANDARDS ARE NOT PROVIDED IN 49 CFR PART 38?
Part 38 provides “minimum guidelines and requirements for accessibility standards in part 37 . . . for transportation vehicles required to be accessible by the Americans With Disabilities...
-
M301.4.1 Clearance in Base (Section-by-Section Analysis)
Three commenters (two manufacturers and one medical association) raised concerns with the six-inch vertical clearance measured from the floor requirement....
-
504.5 Nosings
Risers shall be permitted to slope under the tread at an angle of 30 degrees maximum from vertical....
-
703.2.5 Character Height
Character height measured vertically from the baseline of the character shall be 5/8 inch (16 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter "I"....
-
R405.1 General
Clearances are measured in relation to the usable clear space, not necessarily to the vertical support for an element....
-
7.4.5.1 Size
Vertical alignment at the intersection of the trails that form the T-shaped space shall be nominally level....
-
Spout Location [4.15.3]
The trajectory of water flow must be vertically "parallel" or "nearly parallel" to the face of the unit....
-
§ 38.73(d)(1) Requirements
Vertical alignment may be accomplished by vehicle air suspension, automatic ramps or lifts, or any combination....
-
11B-703.2.5 Character height
Character height measured vertically from the baseline of the character shall be 5/8 inch (15.9 mm) minimum and 2 inches (51 mm) maximum based on the height of the uppercase letter “I”....
-
504.5 Nosings
Risers shall be permitted to slope under the tread at an angle of 30 degrees maximum from vertical....
