Whenever reference is made in these regulations to this section, the findings and determinations required to be rendered by the local enforcing agency shall be subject to ratification through...
Search Results "Vertical Reference Plane"
Filters
Commonly Searched Documents
-
1.9.1.5 Special conditions for persons with disabilities requiring appeals action ratification
-
1131A.1 Changes in level not exceeding ½ inch
When changes in level do occur, they shall be beveled with a slope no greater than 1 unit vertical in 2 units horizontal (50-percent slope)....
-
Areas of Refuge: ADA Standard Section 216.4.2
Section 216.4.2 covers scoping requirements in the current ADA Standards for signs at areas of refuge.
-
5.3.4 Grab Bars
In such cases, the riser shall have vertical or nearly vertical sides and a flat area on each side of the seat that is about 3 inches (75 millimeters) wide....
-
5.3.4 Grab Bars
In such cases, the riser shall have vertical or nearly vertical sides and a flat area on each side of the seat that is about 3 inches (75 millimeters) wide. ...
-
§100.205(e)(1)
(1) Compliance with the appropriate requirements of ICC/ANSI A117.1-2003 (incorporated by reference at §100.201a), ICC/ANSI A117.1-1998 (incorporated by reference at §100.201a), CABO/ANSI...
-
Directional Signs: ADA Standard Section 216.4.3
Section 216.4.3 covers scoping requirements in the current ADA Standards for directional signs.
-
1134A.6, Item 5
When a threshold is used, it shall be a maximum of 2 inches (50.8 mm) in height and have a beveled or sloped angle not exceeding 1 unit vertical in 2 units horizontal (26.6 degrees from...
-
1134A.6, Item 5
When a threshold is used, it shall be a maximum of 2 inches (50.8 mm) in height and have a beveled or sloped angle not exceeding 1 unit vertical in 2 units horizontal (26.6 degrees from...
-
11B-809.10.6.5 Thresholds
Where provided thresholds shall be 2 inches (51 mm) maximum in height and have a beveled or sloped angle not exceeding 1 unit vertical in 2 units horizontal (26.6 degrees from the horizontal...
-
Spaces and Elements: ADA Standard Section 206.2.4
Section 206.2.4 covers the scoping requirements in the most current ADA Standards for accessible routes connecting spaces and elements within a building.
-
11B-404.3.5 Controls
Where push plates, vertical actuation bars or other similar operating devices are provided, they shall be placed in a conspicuous location....
-
11B-306.1 General
Clearances are measured in relation to the usable clear floor space, not necessarily to the vertical support for an element....
-
11B-303.5 Warning curbs
Abrupt changes in level exceeding 4 inches (102 mm) in a vertical dimension between walks, sidewalks or other pedestrian ways and adjacent surfaces or features shall be identified by warning...
-
11B-602.9 Pedestrian protection
When used, wing walls or barriers shall project horizontally at least as far as the drinking fountain and to within 6 inches (152 mm) vertically from the floor or ground surface....
-
Lavatory Fixtures and Vanities
The proposed rule included references to "lavatory fixtures" and to "vanities." Commenters indicated that such references were redundant or inaccurate and should be removed....
-
Boarding Assistance
Carrier personnel are not permitted to physically hand-carry a passenger with a disability on or off a plane, except in the case of an emergency evacuation....
-
Escalators: ADA Standard Section 810.9
Where provided, escalators shall comply with the sections 6.1.3.5.6 and 6.1.3.6.5 of ASME A17.1 (incorporated by reference, see “Referenced Standards” in Chapter 1) and shall have a clear...
-
Platform Lifts: ADA Standard Section 207.2
Section 207.2 covers scoping requirements in the most current ADA Standards for platform lifts used as part of an accessible means of egress.
-
Edge Protection: ADA Standard Section 405.9
Section 405.9 covers the current ADA Standards for edge protection at ramps.
-
1017.5 Tread Obstacles
The vertical alignment of joints in concrete, asphalt, or board surfaces on trails can be tread obstacles....
-
11B-903.6 Structural strength
Allowable stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the seat, fastener, mounting device, or...
-
§100.201 Building entrance on an accessible route
A building entrance that complies with ICC/ANSI A117.1-2003 (incorporated by reference at §100.201a), ICC/ANSI A117.1-1998 (incorporated by reference at §100.201a), CABO/ANSI A117.1-1992...
-
Landscape Forms Inc. Gus Bench Collection
Refined in form and detail, it enables the combination of greenery and camaraderie on a common plane....
