Search Results "Table Height"

• Rulemaking Process Documents > NPRMS > 36 CFR Part 1195 Proposed Accessibility Standards for Medical Diagnostic Equipment NPRM
  M305.2.3 Fittings

  Transfer supports shall not rotate within their fittings.

• Federal Documents > Technical Assistance > 2013 Forest Service Outdoor Recreation Accessibility Guidelines (FSORAG)
  4.1.4 Clear Floor or Ground Space

  At least 48 inches (1220 mm) of clear floor or ground space shall surround the usable sides of a picnic table, measured from the back edge of the benches....

• Rulemaking Process Documents > Committee Activity and Reports > Recommendations on Standards for the Design of Medical Diagnostic Equipment for Adults with Disabilities, Advisory Committee Final Report
  5.4.4 Transfer Support Distance from Transfer Surface Recommendations for M301 and M302

  The above technical criteria would likely result in the transfer surface being located at the foot end of examination tables and allow the use of transfer supports similar to the side rails...

• State and Local Documents > Codes and Standards > 2022 California Standards
  11B-604.8.1.1 Size

  When deployed the baby changing tables shall not obstruct the required width of the accessible route except as allowed by Section 11B-307.2....

• Federal Documents > Preamble to Guidelines > 36 CFR Parts 1190 and 1191 ADA and ABA Accessibility Guidelines - Preamble (Discussion of Comments and Changes)
  Changes in Level and Horizontal Gaps

  This height allows for freight passage while reducing the height of the first step of a rail car above the platform....

• Rulemaking Process Documents > Committee Activity and Reports > Recommendations on Standards for the Design of Medical Diagnostic Equipment for Adults with Disabilities, Advisory Committee Final Report
  MITA Advisory Committee Members

  MITA Advisory Committee Members MINORITY REPORT ON TRANSFER SURFACE HEIGHT RECOMMENDATIONS OF THE U.S. ACCESS BOARD ADVISORY COMMITTEE RE: NPRM: M301.2.1 AND M302.2.1 HEIGHT...

• Rulemaking Process Documents > Committee Activity and Reports > Recommendations on Standards for the Design of Medical Diagnostic Equipment for Adults with Disabilities, Advisory Committee Final Report
  4.3.2 Transfer Surfaces and Imaging Equipment Functions

  These components may, with current designs, impede lowering the table to accessible minimum heights....

• Federal Documents > Technical Assistance > ADA Checklist for New Lodging Facilities
  F. Counter Height

  F. Do the registration counters or other counters serving guests have a lowered portion no more than 36" high or is there a folding shelf at 36" high to allow persons who use...

• Rulemaking Process Documents > Committee Activity and Reports > Recommendations on Standards for the Design of Medical Diagnostic Equipment for Adults with Disabilities, Advisory Committee Final Report
  5.3.1 Permitted Obstructions to Transfer Sides for M301 and M302

  The Committee considered anthropometric data from a research project that examined transfer experience with an adjustable height transfer surface....

• Research and History > Research Documents > Anthropometry of Wheeled Mobility Project: Final Report
  4.3.2 Seat Height

  4.3.2 Seat Height Seat height is an important dimension for establishing the height of built-in seating, toilet heights, tub heights, shower seat heights and other transfer related surfaces...

• Rulemaking Process Documents > Committee Activity and Reports > Recommendations on Standards for the Design of Medical Diagnostic Equipment for Adults with Disabilities, Advisory Committee Final Report
  M301.2.1, M302.2.1 Transfer Height

  M301.2.1, M302.2.1 Transfer Height Proposed requirement: The height of the transfer surface during patient transfer shall be 17 inches (430 mm) minimum and 19 inches (485 mm) maximum...

• Federal Documents > Preamble to Guidelines > 36 CFR Parts 1190 and 1191 ADA and ABA Accessibility Guidelines - Preamble (Discussion of Comments and Changes)
  Route and Destination Signs

  Requirements for route and destination signs are subject to specifications for visual signs in section 703, including character height (810.6.2)....

• Federal Documents > Standards > 36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment
  M305.2.1 Location

  Transfer supports shall comply with M305.2.1.1 or M305.2.1.2 and shall be located 1 ½ inches (38 mm) maximum measured horizontally from the plane defined by the nearest edge of the...

• Federal Documents > Standards > 36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment
  M305.2.4 Cross Section

  Transfer supports shall have a cross section complying with 305.2.4.1 or 305.2.4.2.

• Federal Documents > Standards > 36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment
  M305.2.6 Gripping Surface

  Transfer support gripping surfaces shall be continuous along their length and shall not be obstructed along their tops or sides. The bottoms of transfer support gripping surfaces...

• Federal Documents > Preamble to Standards > 36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment - Preamble
  M305.2.6 Gripping Surfaces (Section-by-Section Analysis)

  The proposed rule did not provide any specific requirements regarding gripping surfaces on transfer supports. However, in the MDE NPRM preamble the Access Board repeatedly noted that...

• Federal Documents > Preamble to Standards > 36 CFR Part 1195 Standards for Accessible Medical Diagnostic Equipment - Preamble
  M305.2.4 Cross Section (Section-by-Section Analysis)

  The proposed rule did not provide specific requirements for the cross section of transfer supports. However, in the MDE NPRM preamble, the Access Board noted that it was considering...

• Rulemaking Process Documents > Committee Activity and Reports > Recommendations on Standards for the Design of Medical Diagnostic Equipment for Adults with Disabilities, Advisory Committee Final Report
  5.4.9 Interruptions along Transfer Support Gripping Recommendation for M301 and M302

  5.4.9 Interruptions along Transfer Support Gripping Recommendation for M301 and M302 Description: Transfer supports may contain elements to provide structural support or prevent...

• Rulemaking Process Documents > Committee Activity and Reports > Recommendations on Standards for the Design of Medical Diagnostic Equipment for Adults with Disabilities, Advisory Committee Final Report
  5.4.1 Transfer Support Location for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position

  5.4.1 Transfer Support Location for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position. Transfer supports should be required on both sides of the transfer surface and...

• Rulemaking Process Documents > Committee Activity and Reports > Recommendations on Standards for the Design of Medical Diagnostic Equipment for Adults with Disabilities, Advisory Committee Final Report
  5.4.2 Transfer Support Length for M301 and M302

  5.4.2 Transfer Support Length for M301 and M302 Description: Transfer support length applies to the gripping surface of the support, that portion of the support used to grasp or...

• Rulemaking Process Documents > Committee Activity and Reports > Recommendations on Standards for the Design of Medical Diagnostic Equipment for Adults with Disabilities, Advisory Committee Final Report
  5.4.6 Transfer Support Gripping Surface Cross Section for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position

  5.4.6 Transfer Support Gripping Surface Cross Section for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position. The gripping surface cross section should comply with the...

• Rulemaking Process Documents > Committee Activity and Reports > Recommendations on Standards for the Design of Medical Diagnostic Equipment for Adults with Disabilities, Advisory Committee Final Report
  5.7.1 Lift Compatibility Clearance in Base for Equipment Used by Patient in Supine, Prone, or Side-Lying Position

  5.7.1 Lift Compatibility Clearance in Base for Equipment Used by Patient in Supine, Prone, or Side-Lying Position.

• Rulemaking Process Documents > Committee Activity and Reports > Recommendations on Standards for the Design of Medical Diagnostic Equipment for Adults with Disabilities, Advisory Committee Final Report
  5.3 Transfer Sides

  5.3 Transfer Sides.

• Rulemaking Process Documents > Committee Activity and Reports > Recommendations on Standards for the Design of Medical Diagnostic Equipment for Adults with Disabilities, Advisory Committee Final Report
  5.4.2 Transfer Support Length for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position

  5.4.2 Transfer Support Length for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position. The transfer support should be a minimum length of 15 inches positioned so that...