All of the seating spaces/work surfaces were approximately 42" high....
Search Results "Surface Smoothness"
Filters
Commonly Searched Documents
-
High work surface
-
11B-302.3 Openings
Openings in floor or ground surfaces shall not allow passage of a sphere more than ½ inch (12.7 mm) diameter except as allowed in Sections 11B-407.4.3 _|Platform to Hoistway Clearance|_,...
-
T302 Walking Surfaces
The technical requirements for walking surfaces include provisions on slip resistance, the maximum size of surface openings, and the maximum height of vertical surface discontinuities (i.e...
-
A4.5.3 Carpet
Much more needs to be done in developing both quantitative and qualitative criteria for carpeting (i.e., problems associated with texture and weave need to be studied). However,...
-
Carpet [§302.2]
Carpet [§302.2] Carpet that is thick, cushiony, or loose impairs accessibility, particularly wheelchair maneuvering. The standards specify the maximum pile height (1/2” measured...
-
14) Carpet and carpet tile
14) Carpet and carpet tile ADAAG: Same standards for carpet and carpet tile: maximum pile height of 1/2" (§4.5.3). UFAS: Carpet must have maximum pile height of 1/2". Carpet...
-
M303.2.5 Surfaces (Section-by-Section Analysis)
The MDE NPRM proposed to require diagnostic equipment used by patients seated in a wheelchair to provide a wheelchair space with a surface that does not slope more than 1:48 in any direction...
-
Acceptable SEWF Systems
Because of their reactivity, the stabilizing binders needed to be applied on site or mixed with EWF no longer than 1 h prior to placement on the ground surface....
-
1133A.4.1, Item 4
Finished flooring shall be extended to the wall beneath the sink and work surface....
-
CONCLUSIONS
For the same reason that people prefer to run on non-paved surfaces, some users would find walking on non-paved surfaces more comfortable as well....
-
4.2.2 Cooking Surface Height
The cooking surface shall be at least 15 inches (380 mm) and no more than 34 inches (865 mm) above the floor or ground surface. ...
-
809.2.1.2 Floor Surfaces
809.2.1.2 Floor Surfaces This section specifies that carpet not be provided on floor surfaces in emergency transportable housing units with mobility features....
-
11B-306.3.3 Minimum required depth
At dining and work surfaces required to be accessible by Section 11B-226.1, knee clearance shall extend 19 inches (483 mm) deep minimum at 27 inches (686 mm) above the finish floor or ground...
-
The Dipstick® Floor Profiler Tool
Calculates F-numbers for runs, sections, and surfaces on site Instantly produces profile graphs on site "Instant" downloading to desktop or laptop computer Automatic zeroing Prints...
-
Tile Tech Pavers® IPE Deck Tiles
If you dislike rough edges, you may have straight reducers in order to smooth out the outer edges of your decking....
-
II. Research Methodology
By 2007 installation of surface materials for testing was begun at Bradford Woods located at Indiana University....
-
III. Results of the Study
Results of the Study The purpose of the longitudinal study was to evaluate a variety of aggregate and organic or natural byproduct soil stabilizer trail surface materials for their ability...
-
Moisture and Durability
these surfacing systems....
-
Exposed Pipes and Surfaces [4.19.4]
Exposed Pipes and Surfaces [4.19.4] To prevent burns, hot water pipes and drain pipes under lavatories must be insulated or otherwise configured to protect against contact....
-
606.5 Exposed Pipes and Surfaces
606.5 Exposed Pipes and Surfaces. Water supply and drain pipes under lavatories and sinks shall be insulated or otherwise configured to protect against contact....
-
804.3 Kitchen Work Surface
804.3 Kitchen Work Surface....
-
408.4.2 Floor Surfaces
408.4.2 Floor Surfaces. Floor surfaces in elevator cars shall comply with 302 and 303....
-
RECOMMENDATIONS
RECOMMENDATIONS An objective test procedure for measuring the firmness and stability of surfaces with a portable device and performance specifications need to be accepted in order to...
-
6. Minimum (Low) Height Standard for Transfer Surfaces
Minimum (Low) Height Standard for Transfer Surfaces As indicated in Section 5.1.1, the MDE Advisory Committee recommends that equipment with transfer surfaces be height adjustable in...
