Proposed 410.6 would require that, where ICT supports real-time voice communication, it must also support RTT functionality....
Search Results "Guy Support"
Filters
Commonly Searched Documents
-
410.6 Real-Time Text Functionality (Section-by-Section Analysis)
-
Free-Standing Overhead Lifts
Free-Standing Overhead Lifts Another type of overhead lift is supported from a frame that rests on the floor....
-
M304.2 Standing Surface (Section-by-Section Analysis)
The requirement for slip resistant and standing supports has been moved under this new requirement applying to standing surfaces....
-
5.8.2.4 Unobstructed Floor Space Recommendation
The base support affects how close the patient can get to the mammography machine because it intrudes into the floor space....
-
M302.1 General
Diagnostic equipment that supports patients in a seated position shall comply with M302. ...
-
11B-903.6 Structural strength
Allowable stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the seat, fastener, mounting device, or supporting...
-
§ 1194.2(a)(2)
(2) When procuring a product, if an agency determines that compliance with any provision of this part imposes an undue burden, the documentation by the agency supporting the procurement...
-
4.26.3(3)
Shear force induced in a fastener or mounting device from the application of 250 lbf (1112N) shall be less than the allowable lateral load of either the fastener or mounting device or the supporting...
-
11B-609.8 Structural strength
Allowable stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the grab bar, fastener, mounting device, or supporting...
-
11B-903.6 Structural strength
Allowable stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the seat, fastener, mounting device, or supporting...
-
Protrusion Limits: ADA Standard Section 307.2
Section 307.2 covers the current ADA Standards for protrusion limits.
-
Classroom Acoustics: ADA Standard Section 6.
Review the updated information on the revisions to the ADA Standards regarding classroom acoustics.
-
Toe Clearance: ADA Standard Section 604.8.1.4
Section 604.8.1.4 covers the current ADA Standards for toe clearance at wheelchair accessible compartments.
-
11B-307.2 Protrusion limits
For example, awnings and their supporting structures cannot reduce the minimum required vertical clearance....
-
M301.1 General
Diagnostic equipment that supports patients in a supine, prone, or side-lying position shall comply with M301. ...
-
11B-602.5 Spout location
The spout shall be located 15 inches (381 mm) minimum from the vertical support and 5 inches (127 mm) maximum from the front edge of the unit, including bumpers. ...
-
4.26.3(4)
a direct tension force of 250 lbf (1112N) plus the maximum moment from the application of 250 lbf (1112N) shall be less than the allowable withdrawal load between the fastener and the supporting...
-
Research Issues
NIH Mission As you all probably know, much of the biomedical research in the United States is supported by the NIH....
-
E207.1 General
EXCEPTION: Software that is assistive technology and that supports the accessibility services of the platform shall not be required to conform to the requirements in Chapter 5....
-
601.1 Scope (Section-by-Section Analysis)
601.1 Scope (Section-by-Section Analysis) This section proposes that the technical requirements for support documentation and services in this chapter be applied where either (a) required...
-
Alterations to cells. (Section-by-Section Analysis)
Only one commenter expressed support for Option I, and a handful of commenters supported Option III. The comments on each option are discussed below....
-
Rakks® Brackets Installation Video
The signature Rakks Style Bracket features a distinctive rectangular bar design that can support shelves up to 24” deep. Rakks style brackets are designed to “underhang” the shelf....
-
602.5 Spout Location
The spout shall be located 15 inches (380 mm) minimum from the vertical support and 5 inches (125 mm) maximum from the front edge of the unit, including bumpers....
-
602.5 Spout Location
The spout shall be located 15 inches (380 mm) minimum from the vertical support and 5 inches (125 mm) maximum from the front edge of the unit, including bumpers....
