[See subsections ...]
Search Results "Ramp Surface"
Filters
Commonly Searched Documents
-
A4.5 GROUND AND FLOOR SURFACES.
-
4.5 GROUND AND FLOOR SURFACES
[See subsections ...]
-
Curb Ramps and Blended Transitions (R309.4) (Section-by-Section Analysis)
Curb Ramps and Blended Transitions (R309.4) (Section-by-Section Analysis) Curb ramps or blended transitions must connect the access aisle serving each accessible on-street parking space...
-
2.2 Surface
The surface of an ORAR shall be firm and stable. The type of surface should be appropriate to the setting and level of development....
-
6f. Ramp Handrails
Are the handrails mounted between 34 and 38 inches above the ramp surface? [ADA Stds 4.8.5] Yes _____ No _____...
-
Handrails Along Walking Surfaces [§403.6, §505]
Handrails Along Walking Surfaces [§403.6, §505] Handrails are required at ramps with a rise greater than 6” and at stairs that are part of a means of egress, but not at other locations...
-
505.7.1 Circular Cross Section
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
11B-505.7.1 Circular cross section
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
11B-505.7.1 Circular cross section
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
11B-505.7.1 Circular cross section
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
6b. Ramp Width
Is the ramp width, measured between handrails, at least 36 inches? [ADA Stds 4.8.3] Yes _____ No _____...
-
505.7.1 Circular Cross Section
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1 1/4 inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
505.7.1 Circular Cross Section
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1 1/4 inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
505.7.1 Circular Cross Section
Handrail gripping surfaces with a circular cross section shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
11B-408.4.2 Floor surfaces
Floor surfaces in elevator cars shall comply with Sections 11B-302 and 11B-303....
-
R404.2 Surfaces
R404.2 Surfaces....
-
6e. Ramp Landing
Is a level landing, at least 60 inches by 60 inches, provided where a ramp changes direction? [ADA Stds 4.8.4] Yes _____ No _____...
-
Section 35.151(i) Curb ramps (Section-by-Section Analysis)
Section 35.151(i) Curb ramps (Section-by-Section Analysis) Section 35.151(e) on curb ramps in the 1991 rule has been redesignated as § 35.151(i)....
-
Dimensional Tolerances in Construction and for Surface Accessibility
[See subsections ...]
-
T405.2 Surfaces
Step tread surfaces shall comply with T302....
-
1132A.9 Smooth surface
Swinging door or gate surfaces within 10 inches (254 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
1132A.9 Smooth surface
Swinging door or gate surfaces within 10 inches (254 mm) of the finish floor or ground measured vertically shall have a smooth surface on the push side extending the full width of the door...
-
404.2.4.4 Floor or Ground Surface
404.2.4.4 Floor or Ground Surface. Floor or ground surface within required maneuvering clearances shall comply with 302. Changes in level are not permitted. EXCEPTIONS: 1....
-
Perpendicular Curb Ramps (R304.2) (Section-by-Section Analysis)
Perpendicular Curb Ramps (R304.2) (Section-by-Section Analysis) Perpendicular curb ramps have a running slope that cuts through or is built up to the curb at right angles or meets the...