For example, in underground parking garages, elevators or, where feasible, pedestrian ramps, are necessary to provide an accessible route from parking levels with accessible spaces to the...
Search Results "Curb Ramp Surface"
-
Is vertical access required to all levels of a parking garage?
-
C. Training
., how to install ramps, the placement of mats over (and not in front of) thresholds). ...
-
Features of Accessible Parking Spaces for Cars
Ramps must not extend into the access aisle. Boundary of the access aisle must be marked. The end may be a squared or curved shape....
-
810.5.3 Platform and Vehicle Floor Coordination--Modification to 810.5.3 of Appendix D to 36 CFR Part 1191
operationally or structurally feasible to meet the horizontal gap or vertical difference requirements of part 1192 or 49 CFR part 38, mini-high platforms, car-borne or platform-mounted lifts, ramps...
-
Section 206.3
The Department is retaining language from former §10.3.1(1), which provides that “Elements such as ramps, elevators, or other circulation devices, fare vending or other ticketing areas,...
-
235.2.1 Dispersion
The term "boat slip" is intended to cover any pier area other than launch ramp boarding piers where recreational boats are moored for purposes of berthing, embarking, or disembarking....
-
235.2.1 Dispersion
The term "boat slip" is intended to cover any pier area other than launch ramp boarding piers where recreational boats are moored for purposes of berthing, embarking, or disembarking....
-
C. Training
., how to install ramps, the placement of mats over (and not in front of) thresholds); and (c) a description of the role of the City’s Election Day Surveyors (EDSs), as set forth in Paragraph...
-
C. Election Judge and Poll Worker Training
., how to install ramps, the placement of mats over (and not in front of) thresholds); and (c) a description of the role of Harris County’s Election Day Surveyors (EDSs), as set forth in...
-
11B-1002.6 Transfer devices for use with amusement rides
Where possible, designers are encouraged to locate the transfer device seat no higher than 17 to 19 inches (430 to 485 mm) above the load and unload surface....
-
1002.6 Transfer Devices for Use with Amusement Rides
Where possible, designers are encouraged to locate the transfer device seat no higher than 17 to 19 inches (430 to 485 mm) above the load and unload surface....
-
R210.3 Shared Use Paths
Objects shall not overhang or protrude into any portion of a shared use path at or below 2.4 m (8.0 ft) measured from the finish surface....
-
Alternative Golf Car Passage
While a golf car passage must be usable by golf cars, it does not necessarily need to have a prepared surface and may be part of a golf car path....
-
4. Wheelchair seat depth
The median seat depth across different wheeled mobility devices would provide a reference value for the depth of other common seating surfaces....
-
COSTS TO LOWER MINIMUM TABLE HEIGHT
The need to reach heights above 32 inches interferes with efforts to lower the transfer surface height....
-
Initial Measures and Transfer Setup
This approach is also widely promoted in rehabilitation research (A Clinical Application Guide to Standardized Wheelchair Seating Measurements of the Body and Seating Support Surfaces, See...
-
3. FIXTURES and HARDWARE
If self-closing valves are used, the faucet shall remain open for at least 10 seconds.”xxii Sinks Exposed Pipes and Surfaces: Hot water and drain pipes under lavatories...
-
The Purpose of FSORAG and FSTAG
has to comply with the guidelines; definitions of terms; and technical requirements defining the physical characteristics of accessible features, such as width, height, slope, length, surface...
-
Standardized Tests of Physical Fitness and Community Ambulation
The subjects rated the level of difficulty from 1 to 10 for both straight travel and turning on the surface using the Level of Difficulty Rating Scale....
-
Multiple Parking Facilities on a Site
., surface lot versus parking garage or deck); dedicated to, and separately serve, different facilities on a site; segmented and separated by guard rails, fencing, or barriers...
-
11B-1002.6 Transfer devices for use with amusement rides
Where possible, designers are encouraged to locate the transfer device seat no higher than 17 to 19 inches (430 to 485 mm) above the load and unload surface....
-
11B-1002.6 Transfer devices for use with amusement rides
Where possible, designers are encouraged to locate the transfer device seat no higher than 17 to 19 inches (430 to 485 mm) above the load and unload surface....
-
1002.6 Transfer Devices for Use with Amusement Rides
Where possible, designers are encouraged to locate the transfer device seat no higher than 17 to 19 inches (430 to 485 mm) above the load and unload surface....
-
1002.6 Transfer Devices for Use with Amusement Rides
Where possible, designers are encouraged to locate the transfer device seat no higher than 17 to 19 inches (430 to 485 mm) above the load and unload surface....