Exception: The knee clearance shall not be reduced at built-in dining and work surfaces required to be accessible by Section 11B-226.1....
Search Results "End Transfer Surface"
-
11B-306.3.4 Clearance reduction
-
5.4.1 Transfer Support Location for M301 and M302
Provisions require transfer supports be provided for use with the transfer sides and be located within reach of the transfer surface and not obstruct transfer onto the surface when in position...
-
M302.3.1 Transfer Supports (Section-by-Section Analysis)
The technical requirements for transfer supports is in M305.2 of the final rule and has been reorganized to mirror the two types of transfer surfaces (end and side) in the final rule for...
-
11B-1002.5.3 Transfer entry
Where openings are provided for transfer to amusement ride seats, the openings shall provide clearance for transfer from a wheelchair or mobility aid to the amusement ride seat....
-
11B-1002.5.3 Transfer entry
Where openings are provided for transfer to amusement ride seats, the openings shall provide clearance for transfer from a wheelchair or mobility aid to the amusement ride seat....
-
11B-1002.5.3 Transfer entry
Where openings are provided for transfer to amusement ride seats, the openings shall provide clearance for transfer from a wheelchair or mobility aid to the amusement ride seat....
-
Surface [1017.2]
The surfaces of trails, passing spaces, and resting intervals must be firm and stable. A firm trail surface resists deformation by indentations....
-
4.7.4 Surface
Surfaces of curb ramps shall comply with 4.5....
-
4.7.4 SURFACE
Surfaces of curb ramps shall comply with 4.5....
-
11B-1008.2.6.1 Accessibility
Ground surfaces shall comply with ASTM F 1951. Ground surfaces shall be inspected and maintained regularly and frequently to ensure continued compliance with ASTM F 1951....
-
11B-1008.2.6.1 Accessibility
Ground surfaces shall comply with ASTM F 1951. Ground surfaces shall be inspected and maintained regularly and frequently to ensure continued compliance with ASTM F 1951....
-
5.4.2 Transfer Support Length for M301 and M302
The transfer support would extend horizontally the entire depth of the transfer surface and would be 15 inches minimum in length....
-
Transfer Height
Transfer Height The height of the transfer device must be between 14 and 24 inches above the load and unload area surface....
-
11B-608.5.1 Transfer type shower compartments
In transfer type shower compartments, the controls, faucets, and shower spray unit shall be installed on the side wall opposite the seat 38 inches (965 mm) minimum and 48 inches (1219 mm...
-
11B-608.5.1 Transfer type shower compartments
In transfer type shower compartments, the controls, faucets, and shower spray unit shall be installed on the side wall opposite the seat 38 inches (965 mm) minimum and 48 inches (1219 mm...
-
403.2 Floor or Ground Surface
403.2 Floor or Ground Surface. Floor or ground surfaces shall comply with 302....
-
Additional Transfer Techniques: Use of Stretchers and Gurneys
Other equipment may be located in spaces with no room at the end of the table making it impossible to position a portable floor lift....
-
Surface [1016.2]
The surfaces of ORARs, passing spaces, and resting intervals must be firm and stable....
-
M305.2.1 Location (Section-by-Section Analysis)
End transfer supports cover diagnostic equipment used by patients in the supine, prone, or side-lying position with end transfer surfaces, M301.2.3.1 in the final rule, and all diagnostic...
-
11B-504.4 Tread surface
Stair treads shall comply with Section 11B-302. Changes in level, slopes exceeding 1:48, and detectable warnings shall not be permitted. Exception: Reserved.
-
11B-504.4 Tread surface
Stair treads shall comply with Section 11B-302. Changes in level, slopes exceeding 1:48, and detectable warnings shall not be permitted. Exception: Reserved.
-
5.1.7 Surface
The surface of the clear ground space shall be firm and stable. ...
-
1008.3 Transfer Systems
1008.3 Transfer Systems. Where transfer systems are provided to connect to elevated play components, transfer systems shall comply with 1008.3. Advisory 1008.3 Transfer Systems....
-
1002.5.2 Transfer Height
The height of amusement ride seats designed for transfer shall be 14 inches (355 mm) minimum and 24 inches (610 mm) maximum measured from the surface of the load and unload area....