The height of transfer device seats shall be 14 inches (355 mm) minimum and 24 inches (610 mm) maximum measured from the load and unload surface....
Search Results "End Transfer Surface"
Filters
Commonly Searched Documents
-
1002.6.2 Transfer Height
-
1002.6.2 Transfer Height
The height of transfer device seats shall be 14 inches (355 mm) minimum and 24 inches (610 mm) maximum measured from the load and unload surface....
-
Suggested accessibility guidelines for exterior concrete surfaces
The following tolerances may be applicable for exterior accessible surfaces....
-
403 Walking Surfaces
403 Walking Surfaces...
-
Envirobond Organic-Lock™ Surface Stabilizer
Important features of a surface stabilized with Organic-Lock™ include: Erosion Control - Organic-Lock stabilized surfaces offer significantly improved resistance to erosion over...
-
3.1.2 Surface of Vehicle Parking Spurs
The surface of vehicle parking spurs shall be firm and stable. The type of surface should be appropriate to the setting and level of development....
-
5.3.2.2 Surface
The surface of the turning space and clear floor or ground space shall be firm and stable. ...
-
304.2 Floor or Ground Surfaces
304.2 Floor or Ground Surfaces. Floor or ground surfaces of a turning space shall comply with 302. Changes in level are not permitted....
-
4.7.4 Surface
The surface of the clear floor or ground spaces required by section 4.0 shall be firm and stable. The type of surface should be appropriate to the setting and level of development....
-
4.8.6 Cross Slope and Surfaces
The cross slope of ramp surfaces shall be no greater than 1:50. Ramp surfaces shall comply with 4.5....
-
4.8.6 CROSS SLOPE AND SURFACES
The cross slope of ramp surfaces shall be no greater than 1:50. Ramp surfaces shall comply with 4.5....
-
4.5.4 Surface
The surface of the clear floor or ground space for trash, recycling, and other essential containers shall be firm and stable....
-
304.2 Floor or Ground Surfaces
Floor or ground surfaces of a turning space shall comply with 302. Changes in level are not permitted. EXCEPTION: Slopes not steeper than 1:48 shall be permitted....
-
304.2 Floor or Ground Surfaces
Floor or ground surfaces of a turning space shall comply with 302. Changes in level are not permitted....
-
7.4.1 Surface
The trail tread surface, including resting intervals and passing spaces, shall be both firm and stable....
-
Figure 1009.5.1 Size of Transfer Platform – Drawing from the U.S. Access Board
-
5.4.1 Transfer Support Location for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
5.4.1 Transfer Support Location for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position....
-
4.3.4 Tent Pad or Platform Surface
Tent pads and platforms shall have a surface that is firm and stable and is designed to allow use of tent stakes and other tent securing devices. Exception. ...
-
5.4.2 Transfer Support Length for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
5.4.2 Transfer Support Length for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position....
-
Selection of Trail Surface Materials
Selection of Trail Surface Materials A review of trail surfacing products conducted for this project identified approximately 80 different trail surface materials that promoted providing...
-
11B-1002.5 Amusement ride seats designed for transfer
Ride seats designed for transfer should involve only one transfer....
-
11B-1002.5 Amusement ride seats designed for transfer
Ride seats designed for transfer should involve only one transfer....
-
11B-1002.5 Amusement ride seats designed for transfer
Ride seats designed for transfer should involve only one transfer....
-
(3) Transfers of Privately Held Equity Interests
(3) Transfers of Privately Held Equity Interests: A transfer of interest in a Brand Hotel in which, after conveyance of the interest, a 25% or more cumulative interest in the Brand Hotel...
