(gap) between the wheeled mobility device and the piece of medical equipment increased and cautioned against speculating that height differences between the wheeled mobility device and transfer...
Search Results "End Transfer Surface"
-
18 Inch Low Height
-
Transfer Surface Size – M301.2.2 Supine, Prone, or Side-Lying Position
Transfer Surface Size – M301.2.2 Supine, Prone, or Side-Lying Position The issues were discussed and decided in the full committee meeting as follows: depth of 17 inches minimum and width...
-
5.2.1.1 Transfer Surface Width Recommendations for M301
5.2.1.1 Transfer Surface Width Recommendations for M301 The Committee recommends a transfer surface of 28 inches minimum width for equipment used by patients in a supine, side-lying,...
-
10. Can a transfer platform be an irregular shape as long as it incorporates the minimum rectangle of 14 by 24 inches?
Can a transfer platform be an irregular shape as long as it incorporates the minimum rectangle of 14 by 24 inches? Yes....
-
Transfer Height
Transfer Height Ride seats designed for transfer must be between 14 and 24 inches above the load and unload area surface....
-
Surface and Slope [1012.4 and 1012.5]
The surface of parking spaces and pull-up spaces for RVs must be firm and stable....
-
11B-302.2 Carpet
Exposed edges of carpet shall be fastened to floor surfaces and shall have trim on the entire length of the exposed edge. Carpet edge trim shall comply with Section 11B-303....
-
11B-302.2 Carpet
Exposed edges of carpet shall be fastened to floor surfaces and shall have trim on the entire length of the exposed edge. Carpet edge trim shall comply with Section 11B-303....
-
Two Step Transfers Attainable Heights
Among the participants that were able to complete the two step transfers, the 5th percentile were able to transfer to a second platform that was 3 inches higher than the first platform for...
-
Performance for Surface Firmness and Stability
Performance for Surface Firmness and Stability Table 1 identifies the 11 test surface materials, the dates of installation, and the date of the initial and final testing of surfaces at...
-
M301.2.2, M302.2.2 Transfer Size
M301.2.2, M302.2.2 Transfer Size Proposed requirement: 30" wide minimum and 15" deep minimum • Sub-Committee Recommendation: 28" wide minimum and 17" deep minimum....
-
11B-1009.5.7 Grab bars
At least one grab bar on each transfer step and the transfer platform or a continuous grab bar serving each transfer step and the transfer platform shall be provided....
-
11B-1009.5.7 Grab bars
At least one grab bar on each transfer step and the transfer platform or a continuous grab bar serving each transfer step and the transfer platform shall be provided....
-
Grab Bars: ADA Standard Section 1009.5.7
At least one grab bar on each transfer step and the transfer platform or a continuous grab bar serving each transfer step and the transfer platform shall be provided....
-
Dining Surface and Work Surface
Commenters expressed concern about use of the terms "dining surfaces" and "work surfaces" and urged the Board to include definitions of the terms in the final rule....
-
Must accessible surfaces be paved?
Concrete, asphalt, and other paved surfaces are more reliably compliant, but other materials, such as wood, and construction methods can be used to provide firm and stable surfaces. ...
-
TRANSFER STALLS
[See subsections ...]
-
Exterior Surfaces
However, some natural surfaces, such as compacted earth, soil treated with consolidants, or materials stabilized and retained by permanent or temporary geotextiles (mesh), gridforms, or...
-
Surfaces of Trails
Trail surfaces must be firm and stable....
-
1017.2 Surface
This section requires the surface of trails, passing spaces, and resting intervals to be firm and stable. A firm trail surface resists deformation by indentations....
-
11B-604.8.1.1.3 Maneuvering space with end-opening door
In a wheelchair accessible compartment with a door located in the front wall or partition (facing the water closet), either in-swinging or out-swinging, a minimum 60 inches (1524 mm)...
-
Surface and Slope [1015.5 and 1015.6]
The surface of clear ground spaces and turning spaces must be firm and stable....
-
11B-302.1 General
A firm surface resists deformation by either indentations or particles moving on its surface....
-
11B-302.1 General
A firm surface resists deformation by either indentations or particles moving on its surface....