Seat [4.21.3] ADAAG specifies maximum seat dimensions. Minimum dimensions contained in the CABO-ANSI A117.1‒1992 standard are acceptable....
Search Results "Elongated Water Closet Seat"
Filters
Commonly Searched Documents
-
Seat [4.21.3]
-
Team and Player Seating
A provision for team and player seating areas is included in the final rule (221.2.1.4)....
-
610.3.1 Rectangular Seats
The rear edge of a rectangular seat shall be 2 1/2 inches (64 mm) maximum and the front edge 15 inches (380 mm) minimum and 16 inches (405 mm) maximum from the seat wall....
-
Transfer Height: ADA Standard Section 1002.5.2
The height of amusement ride seats designed for transfer shall be 14 inches (355 mm) minimum and 24 inches (610 mm) maximum measured from the surface of the load and unload area....
-
Structural Strength: ADA Standard Section 610.4
Section 610.4 covers the current ADA Standards for the structural strength of seats.
-
11B-610.4 Structural strength
Allowable stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the seat, fastener, mounting device, or...
-
Water Hydrants and Water Spouts [1011.2, 1011.3, and 1011.6]
Water hydrants are outdoor devices for dispensing water, including water faucets on posts and hand pumps. The opening for dispensing the water is called a water spout....
-
1607A.9.2 Grab bars, shower seats and accessible benches
Grab bars, shower seats and accessible benches shall be designed to resist a single concentrated load of 250 pounds (1.11 kN) applied in any direction at any point on the grab bar, shower...
-
Wall furr-out to support a grab bar when toilet is too far from the side wall
Here's a good example of one solution for a water closet that's too far from the adjacent side wall. ...
-
Companion Seats: ADA Standard Section 1002.4.7
Where the interior width of the amusement ride is greater than 53 inches (1345 mm), seating is provided for more than one rider, and the wheelchair is not required to be centered within...
-
Sioux Chief FullFlush™ Offset Flange 889-AOM
½" offset in any direction for closet bowl setting Corrosion-resistant 430 stainless steel swivel ring is engineered for maximum strength Black...
-
4.21.3 SEAT
A seat shall be provided in shower stalls 36 in by 36 in (915 mm by 915 mm) and shall be as shown in Fig. 36....
-
4.21.3 Seat
A seat shall be provided in shower stalls 36 in by 36 in (915 mm by 915 mm) and shall be as shown in Fig. 36....
-
(1)(a)
overlap a maximum of 19 inches (485 mm), if the lowest portion of the fixture is a minimum of 29 inches (740 mm) above the floor, provided such fixtures do not interfere with access to the water...
-
604.5 Grab Bars
Grab bars for water closets shall comply with 609. Grab bars shall be provided on the side wall closest to the water closet and on the rear wall. EXCEPTIONS: 1....
-
11B-610.3.1 Rectangular seats
11B-610.3.1 Rectangular seats....
-
11B-1008.4.4 Entry points and seats
Where play components require transfer to entry points or seats, the entry points or seats shall be 11 inches (279 mm) minimum and 24 inches (610 mm) maximum from the clear floor or ground...
-
11B-610.3.1 Rectangular seats
The rear edge of a rectangular seat shall be 2½ inches (64 mm) maximum and the front edge 15 inches (381 mm) minimum and 16 inches (406 mm) maximum from the seat wall....
-
604.5 Grab Bars
Grab bars for water closets shall comply with 609. Grab bars shall be provided on the side wall closest to the water closet and on the rear wall....
-
604.5 Grab Bars
Grab bars for water closets shall comply with 609. Grab bars shall be provided on the side wall closest to the water closet and on the rear wall. EXCEPTIONS: 1....
-
III-7.5175 Fixed seating
III−7.5175 Fixed seating (ADAAG §4.1.3(18)). At least five percent of fixed or built-in seating or tables must be accessible....
-
604.5.2 Rear Wall Grab Bar Location
This video demonstrates how to take the measurements of the length of a rear grab bar and the lateral position of a rear grab bar.
-
11B-610.3.1 Rectangular seats
The rear edge of a rectangular seat shall be 2½ inches (64 mm) maximum and the front edge 15 inches (381 mm) minimum and 16 inches (406 mm) maximum from the seat wall....
-
11B-609.1 General
Grab bars in toilet facilities and bathing facilities shall comply with Section 11B-609.
