11B-610 Seats....
Search Results "Elongated Water Closet Seat"
Filters
Commonly Searched Documents
-
11B-610 Seats
-
Wall furr-out to support a grab bar when toilet is too far from the side wall
Here's a good example of one solution for a water closet that's too far from the adjacent side wall. ...
-
Recessed Lavatories
The rear grab bar determines the minimum distance of the lavatory from the water closet....
-
Seating
Seating:...
-
Oatey Level Fit Offset Closet Flange Metal Ring 43501 - PVC
The metal ring provides added strength and cracking resistance to the flange and can be rotated to allow precise alignment of bolts and screws. Solvent welds inside of 4" or...
-
11B-203.11 Water slides
11B-203.11 Water slides. Water slides shall not be required to comply with these requirements or to be on an accessible route....
-
Boost Your Business - Chapter 10 - Restroom Fixtures
Boost Your Business - Chapter 10 - Restroom Fixtures
-
1. Accessible toilet
1. Accessible toilet with rear and side grab bars, clear floor space for wheelchair transfer, and an accessible flush valve.
-
1607.9.2 Grab bars, shower seats and accessible benches
Grab bars, shower seats and accessible benches shall be designed to resist a single concentrated load of 250 pounds (1.11 kN) applied in any direction at any point on the grab bar, shower...
-
Figure 604.5.1 Side Wall Grab Bar at Water Closets – Drawing from the U.S. Access Board
-
610.3.1 Rectangular Seats
610.3.1 Rectangular Seats....
-
Type: ADA Standard Section 802.3.2
Companion seats shall be equivalent in size, quality, comfort, and amenities to the seating in the immediate area. Companion seats shall be permitted to be movable....
-
11B-802.3.2 Type
Companion seats shall be equivalent in size, quality, comfort, and amenities to the seating in the immediate area. Companion seats shall be permitted to be movable....
-
Entry Points and Seats: ADA Standard Section 1008.4.4
Where play components require transfer to entry points or seats, the entry points or seats shall be 11 inches (280 mm) minimum and 24 inches (610 mm) maximum from the clear floor or ground...
-
Oatey Level Fit Offset Closet Flange Metal Ring 43804 - PVC Bulk
The metal ring provides added strength and cracking resistance to the flange and can be rotated to allow precise alignment of bolts and screws. Solvent welds inside of 4" or...
-
Oatey Level Fit Offset Closet Flange Metal Ring 43500 - ABS 15150
The metal ring provides added strength and cracking resistance to the flange and can be rotated to allow precise alignment of bolts and screws. Solvent welds inside of 4" or...
-
610.3.1 Rectangular Seats
The rear edge of a rectangular seat shall be 2½ inches (64 mm) maximum and the front edge 15 inches (380 mm) minimum and 16 inches (405 mm) maximum from the seat wall....
-
Transfer Height: ADA Standard Section 1002.5.2
The height of amusement ride seats designed for transfer shall be 14 inches (355 mm) minimum and 24 inches (610 mm) maximum measured from the surface of the load and unload area....
-
Structural Strength: ADA Standard Section 610.4
Section 610.4 covers the current ADA Standards for the structural strength of seats.
-
11B-610.4 Structural strength
Allowable stresses shall not be exceeded for materials used when a vertical or horizontal force of 250 pounds (1112 N) is applied at any point on the seat, fastener, mounting device, or...
-
11B-604.5 Grab bars
Grab bars for water closets shall comply with Section 11B-609. Grab bars shall be provided on the side wall closest to the water closet and on the rear wall....
-
Seat [4.21.3]
Seat [4.21.3] ADAAG specifies maximum seat dimensions. Minimum dimensions contained in the CABO-ANSI A117.1‒1992 standard are acceptable....
-
Team and Player Seating
A provision for team and player seating areas is included in the final rule (221.2.1.4)....
-
610.3.1 Rectangular Seats
The rear edge of a rectangular seat shall be 2 1/2 inches (64 mm) maximum and the front edge 15 inches (380 mm) minimum and 16 inches (405 mm) maximum from the seat wall....
