and not to state any tolerance in conjunction with the specified dimension....
Search Results "Dimension Range"
-
3. MINIMUMS, MAXIMUMS AND SPECIFYING AT THE LIMIT
-
Parallel Grab Bars
In finalizing this rule, the Board has sought to specify dimensions as a range instead of in absolute terms where possible to facilitate compliance without compromising accessibility....
-
1. Thigh Breadth
Thigh breadth for this analysis was computed as the larger of two dimensions, the horizontal distance between the lateral (outer) aspect of the hips, and the horizontal distance between...
-
Truncated Domes
In the final rule, the Board has revised the specification for the diameter and spacing of truncated domes to permit a range of dimensions (705.1.1)....
-
Verify Framing
bars in bathtub/shower rooms. 11B-610 Width and depth of shower stalls. 11B-608.2 Drinking fountain alcoves/wing walls. 11B-602.9 Tread dimensions...
-
Verify Framing
bars in bathtub/shower rooms. 11B-610 Width and depth of shower stalls. 11B-608.2 Drinking fountain alcoves/wing walls. 11B-602.9 Tread dimensions...
-
Figure 810.2.2 Dimensions of Bus Boarding and Alighting Areas – Drawing from the U.S. Access Board
-
604.6 Flush Control Reach Range
-
4.4.1 Overview of Mammography Accessibility Considerations
Critical considerations in this redesign include the physical constraints needed for operation of the equipment, technical feasibility, patient safety, clinical standards, and the range...
-
304 Turning Space
Comments urged that the minimum dimensions for turning space be increased to better accommodate scooters and motorized wheelchairs....
-
Ambulatory Accessible Compartment
Throughout the new guidelines, the Board has sought to specify dimensions as a range instead of in absolute terms where practicable to facilitate compliance without compromising accessibility...
-
Non-Circular Cross Section: ADA Standard Section 609.2.2
Section 609.2.2 covers the current ADA Standards for non-circular grab bar cross sections.
-
11B-609.2.2 Non-circular cross section
Grab bars with non-circular cross sections shall have a cross-section dimension of 2 inches (51 mm) maximum and a perimeter dimension of 4 inches (102 mm) minimum and 4.8 inches (122 mm)...
-
11B-609.2.2 Non-circular cross section
Grab bars with non-circular cross sections shall have a cross-section dimension of 2 inches (51 mm) maximum and a perimeter dimension of 4 inches (102 mm) minimum and 4.8 inches (122 mm)...
-
Non-Circular Cross Sections: ADA Standard Section 505.7.2
Section 505.7.2 covers the current ADA Standards for the non-circular cross section of handrail gripping surfaces.
-
11B-505.7.2 Non-circular cross sections
Handrail gripping surfaces with a non-circular cross section shall have a perimeter dimension of 4 inches (102 mm) minimum and 6¼ inches (159 mm) maximum, and a cross-section dimension of...
-
11B-505.7.2 Non-circular cross sections
Handrail gripping surfaces with a non-circular cross section shall have a perimeter dimension of 4 inches (102 mm) minimum and 6¼ inches (159 mm) maximum, and a cross-section dimension of...
-
Grab bars
The outside diameter dimension range for circular cross-section grab bars are between 1.25 and 2 inches. A 1.5 inch diameter was chosen for the study....
-
Eco Grip Flooring 2min HD
Eco-Grip slip resistant flooring offers a new dimension in safe flooring....
-
11B-302.3 Openings
Elongated openings shall be placed so that the long dimension is perpendicular to the dominant direction of travel. Advisory 11B-302.3 Openings....
-
11B-302.3 Openings
Elongated openings shall be placed so that the long dimension is perpendicular to the dominant direction of travel. Advisory 11B-302.3 Openings....
-
Figure 408.4.1(a) Limited-Use/Limited-Application (LULA) Elevator Car Dimensions – Drawing from the U.S. Access Board
-
11B-407.4.6.2.1 Size and shape
Buttons shall have square shoulders, be ¾ inch (19.1 mm) minimum in their smallest dimension and be raised 1/8 inch (3.2 mm) plus or minus 1/32 inch (0.8 mm) above the surrounding surface...
-
11B-407.4.6.2.1 Size and shape
Buttons shall have square shoulders, be ¾ inch (19.1 mm) minimum in their smallest dimension and be raised 1/8 inch (3.2 mm) plus or minus 1/32 inch (0.8 mm) above the surrounding surface...
