These dimensions apply to either forward or side reaches....
Search Results "Dimension"
-
308.1 General
-
11B-308.1 General
These dimensions apply to either forward or side reaches....
-
Platform Edges
This depth is an absolute dimension, not a minimum. Some platforms are edged with a buffer material that is designed to break away if hit by cargo trains....
-
Space Allowance and Reach Ranges [4.2]
Adult dimensions and measures for standard manual wheelchairs form the basis of many ADAAG specifications....
-
505.6 Gripping Surface
distance between horizontal projections and the bottom of the gripping surface shall be permitted to be reduced by 1/8 inch (3.2 mm) for each 1/2 inch (13 mm) of additional handrail perimeter dimension...
-
4.4.4 Clear Floor or Ground Space
The long dimension of the clear space shall be roughly perpendicular to the length of the bench....
-
Department of Justice method
Use the tape measure and measure the open gap at the downhill end of the level to establish the critical dimension....
-
11B-405.7.5 Doorways
Doors, in any position, shall not reduce the minimum dimension of the ramp landing to less than 42 inches (1067 mm). [2010 ADAS] 405.7.5 Doorways....
-
11B-308.1 General
These dimensions apply to either forward or side reaches....
-
11B-308.1 General
These dimensions apply to either forward or side reaches....
-
11B-703.7.2.1 International Symbol of Accessibility
A border may be provided inside or outside of the minimum required International Symbol of Accessibility dimension....
-
Selection of Variables
] E Measurements of chair and user (floor to top of head, side to side, back to front, height to armrest, height to seat) [accessibility] The two most basic dimensions...
-
Can parking signage height be considered a "safe harbor"?
No specific height dimension given. For an older property with parking signs mounted at, say 45" inches to the bottom, are these protected by the safe harbor rule? ...
-
Station 5-Lateral Operating Space (Sweep Width)
Space requirements of transportation users are one of the essential inputs in facility design, particularly in determining cross-sectional dimension needs of facilities....
-
4.3.4 Knee and Toe Clearances
The following dimensions on knee and toe clearances should be used to accommodate 95% of our study sample on all four dimensions: • Toe clearance depth: 127 mm (5 in.) maximum, measured...
-
Combination Wheelchair/Horse Accessible Gates
The gate dimensions work well together because the required turning diameter for a wheelchair is 60 inches....
-
5.4.5.1 Transfer and Positioning Support Position Recommendation for Imaging Equipment
5.4.5.1 Transfer and Positioning Support Position Recommendation for Imaging Equipment On imaging equipment, the transfer surface is oriented along the long dimension of the surface where...
-
Clear Floor Space [4.35.2]
Recommendations: Consider additional space on the narrow dimension to allow alternative transfers. Some people may need to fully recline to dress or change clothes....
-
4.21.2 Size and Clearances
Institutional showers exceeded the minimum stall dimensions....
-
11B-703.7.2.1 International Symbol of Accessibility
A border may be provided inside or outside of the minimum required International Symbol of Accessibility dimension. [2010 ADAS] 703.7.2.1 International Symbol of Accessibility....
-
11B-812.10.4 Location
Where the long dimension of a vehicle space is parallel to the vehicular way, the EV charger shall be adjacent to, and 48 inches (1219 mm) maximum from the head end or foot end of the vehicle...
-
4.3.1 Reference WhMD Users
The Reference Users should include plan and elevation drawings and have key dimensions coded with a corresponding table of values for each code showing the 5th, 25th, 50th, 75th and 95th...
-
4.2 Applications of Findings in Design and Standards Development
Even dimensions that accommodate our entire sample might not accommodate someone who is larger or smaller than the people we measured....