The Reference Users should include plan and elevation drawings and have key dimensions coded with a corresponding table of values for each code showing the 5th, 25th, 50th, 75th and 95th...
Search Results "Dimension"
Filters
Commonly Searched Documents
-
4.3.1 Reference WhMD Users
-
Combination Wheelchair/Horse Accessible Gates
The gate dimensions work well together because the required turning diameter for a wheelchair is 60 inches....
-
5.4.5.1 Transfer and Positioning Support Position Recommendation for Imaging Equipment
5.4.5.1 Transfer and Positioning Support Position Recommendation for Imaging Equipment On imaging equipment, the transfer surface is oriented along the long dimension of the surface where...
-
Clear Floor Space [4.35.2]
Recommendations: Consider additional space on the narrow dimension to allow alternative transfers. Some people may need to fully recline to dress or change clothes....
-
4.21.2 Size and Clearances
Institutional showers exceeded the minimum stall dimensions....
-
11B-703.7.2.1 International Symbol of Accessibility
A border may be provided inside or outside of the minimum required International Symbol of Accessibility dimension. [2010 ADAS] 703.7.2.1 International Symbol of Accessibility....
-
11B-812.10.4 Location
Where the long dimension of a vehicle space is parallel to the vehicular way, the EV charger shall be adjacent to, and 48 inches (1219 mm) maximum from the head end or foot end of the vehicle...
-
4.2 Applications of Findings in Design and Standards Development
Even dimensions that accommodate our entire sample might not accommodate someone who is larger or smaller than the people we measured....
-
IDEA Center
This occurs mostly with dimensions near the hands and other body parts that may move slightly during data collection....
-
A4.22.3 Clear Floor Space
Figure 28 (section 4.16) provides minimum clear floor space dimensions for toilets in accessible “unisex” toilet rooms....
-
Appendix 3 - Comparison of US Standards to IDEA Center Research
Appendix 3 - Comparison of US Standards to IDEA Center Research Dimension U.S....
-
1133B.5.4.5
Intermediate and bottom landings at a change of direction in excess of 30 degrees shall have a dimension in the direction of ramp run of not less than 72 inches (1829 mm) to accommodate...
-
Section 5 References
“Revised Knee Clearance Depth and Footrest Clearance dimensions for sizing of mammography equipment.” Memorandum. April 23, 2013....
-
Seat width and depth
This dimension is within the range of seat depths allowed for transfer steps in play and pool areas and for proposed diagnostic equipment (14 to 17 inches). ...
-
Openings in Trail Surfaces
Place elongated openings more than a quarter of an inch wide with the long dimension perpendicular or diagonal to the primary direction of travel (figure 138)....
-
Structure Sensor 3D Depth Scanning Software for 3D Imaging and Printing
The magic of 3D depth sensing begins with the ability to capture fast, accurate, dimensions of objects and environments....
-
4.1 Introduction
To provide realistic guidance for designers, information on wheeled mobility dimensions should include occupied sizes as well as device size; both in percentile form, and also include accessories...
-
4. COMMON PATH OF TRAVEL ITEMS
area of alteration • Public telephones serving the area of alteration • Exterior or interior signs along the path of travel • Accessible route components • Walking surfaces dimensions...
-
Parallel Curb Ramps (R304.3) (Section-by-Section Analysis)
Where the turning space is constrained on two or more sides, the turning space must be 1.2 meters (4 feet) minimum by 1.5 meters (5 feet) minimum, with the 1.5 meters (5 feet) dimension...
-
T-turn Maneuvering Space
The Department has decided to delete the reference to the T-turn dimensions in the Guidelines for Requirement 4....
-
Size and Spacing of Grab Bars and Handrails [4.26.2]
The 1½ inch clearance between walls and handrails or grab bars is an absolute dimension; it provides knuckle clearance while generally disallowing entrapment of the forearm or elbow....
-
Alterations: Alternate Stalls
Wheelchair maneuvering and transfer can be very difficult or impossible within these dimensions which is why these designs are permitted only in alterations where "technical infeasibility...
-
11B-505.6 Gripping surface
distance between horizontal projections and the bottom of the gripping surface shall be permitted to be reduced by 1/8 inch (3.2 mm) for each ½ inch (12.7 mm) of additional handrail perimeter dimension...
-
Omnia Industries Inc. Modern Narrow Backset Lever Lockset - Solid Brass No.64036
Modern Narrow Backset Lever Lockset - Solid Brass Dimensions: 8-1/4" Overall Finishes: US3, US26, US26D Notes: Shown in US26...
