The signal shall be an automatic verbal annunciator which announces the floor at which the car is about to stop....
Search Results "Floor-Level Exit Sign"
Filters
Commonly Searched Documents
-
11B-411.4.8.2.1 Signal type
-
602.4 Spout Height
Spout outlets shall be 36 inches (915 mm) maximum above the finish floor or ground....
-
602.4 Spout Height
Spout outlets shall be 36 inches (915 mm) maximum above the finish floor or ground....
-
11B-602.4 Spout height
Spout outlets shall be 36 inches (914 mm) maximum above the finish floor or ground....
-
4.24.2 HEIGHT
Sinks shall be mounted with the counter or rim no higher than 34 in (865 mm) from the floor....
-
11B-411.4.8.2.1 Signal type
The signal shall be an automatic verbal annunciator which announces the floor at which the car is about to stop....
-
11B-602.4 Spout height
Spout outlets shall be 36 inches (914 mm) maximum above the finish floor or ground....
-
11B-411.4.8.2.1 Signal type
The signal shall be an automatic verbal annunciator which announces the floor at which the car is about to stop....
-
11B-813.2.1 Adult changing table
Adult changing tables shall be fixed to the floor or a wall and shall comply with Section 11B-813.2.1....
-
Stopping Distance
for the Development of Bicycle Facilities (pp. 40-42) uses a perception-reaction time of 2.5 seconds.(2) For this study, the perception-reaction time was measured from when the STOP sign...
-
Auxiliary Aids and Services
For people who are deaf, have hearing loss, or are deaf-blind, this includes providing a qualified notetaker; a qualified sign language interpreter, oral interpreter, cued-speech interpreter...
-
2010 ADA Standards
“1½ inches plus or minus X inches. ”Where the requirement states a specified range, such as in Section 609.4 where grab bars must be installed between 33 inches and 36 inches above the floor...
-
104.1.1 Construction and Manufacturing Tolerances
Where the requirement states a specified range, such as in Section 609.4 where grab bars must be installed between 33 inches and 36 inches above the floor, the range provides an adequate...
-
104.1.1 Construction and Manufacturing Tolerances
Where the requirement states a specified range, such as in 609.4 where grab bars must be installed between 33 inches and 36 inches above the floor, the range provides an adequate tolerance...
-
1008.3.2 Transfer Steps
Transfer steps shall be provided where movement is intended from transfer platforms to levels with elevated play components required to be on accessible routes....
-
1009.2.8 Submerged Depth
The lift shall be designed so that the seat will submerge to a water depth of 18 inches (455 mm) minimum below the stationary water level....
-
STEP 1 Assess your play area design
STEP 1 Assess your play area design This step identifies the number and different types of ground level play components provided in a play area design. ...
-
406.2 Counter Slope
The adjacent surfaces at transitions at curb ramps to walks, gutters, and streets shall be at the same level....
-
R305.2.7 Boarding and Alighting Areas
At boarding and alighting areas at sidewalk or street level transit stops for rail vehicles, detectable warning surfaces shall be placed at the side of the boarding and alighting area facing...
-
(4) [sic] Thresholds at exterior doors
Subject to the exceptions for thresholds and changes in level at exterior areas constructed of impervious materials, the final Guidelines continue to specify that thresholds at exterior...
-
§ 35.151(i)(1)
(1) Newly constructed or altered streets, roads, and highways must contain curb ramps or other sloped areas at any intersection having curbs or other barriers to entry from a street level...
-
§ 37.91(d)
(d) Unless not practicable, a person providing intercity rail transportation shall place an accessible car adjacent to the end of a single level dining car through which an individual who...
-
11B-703.7.1 Finish and contrast
Signs are more legible for persons with low vision when characters contrast as much as possible with their background....
-
11B-407.4.7.2 Keypads
Keypads shall be identified by characters complying with Section 11B-703.5 _|Signs; Visual Characters|_ and shall be centered on the corresponding keypad button....