standard includes additional provisions for runway enclosures, electrical equipment and wiring, structural support, headroom clearance (which is 80 inches minimum), lower level access ramps...
Search Results "Curb Ramp Surface"
Filters
Commonly Searched Documents
-
ASME
-
Bradley 20.6 Gallon Waste Receptacle 355
Model 355 Surface Mounted 20.6 Gallon Capacity Surface Mounted...
-
Rebuilding Together Nashville - Nashville, TN
The most common repairs performed by RTN are floor repairs, accessibility modifications for seniors, plumbing work, electrical work, and the addition or repair of exterior wheelchair ramps...
-
Rebuilding Together Twin Cities - Minneapolis, MN
primary needs: Accessibility, Livability and Community: Accessibility Services: Safe at Home Program provides volunteer-delivered safety and fall prevention modifications and ramps...
-
Shared Use Paths: ADA Standard Section 2.
address access to sidewalks, streets, and other pedestrian facilities, provide requirements for pedestrian access routes, including specifications for route width, grade, cross slope, surfaces...
-
11B-609.3 Spacing
Section 11B-609.9 the space between the walls and the grab bar shall be 1½ inches (38 mm) minimum for a distance of 6 inches on either side of the inside corner between two adjacent wall surfaces...
-
What is a "reasonable accommodation"?
Some of the most common types of accommodations include: physical changes, such as installing a ramp or modifying a workspace or restroom; sign language interpreters for people...
-
Accessibility to Perform the Essential Functions of the Job
Examples of accommodations that may be needed to make facilities accessible and usable include: installing a ramp at the entrance to a building; removing raised thresholds...
-
Part One: The ADA’s Requirements for Small Towns
A ramp located next to the stairs to this town hall provides an accessible entrance. 1 The term "towns" is used in this publication to refer to all small local governments, towns, and...
-
10 - foot straightedge method
For ramps ACI 117 refers to RMS Levelness tolerance as defined in paragraph 4.11 in ASTM E - 1486....
-
Expert opinion on the current knowledge
None of the research identified described how well individuals are able to overcome physical barriers in between the wheelchair and target surfaces. ...
-
11B-403.5.1 Clear width
Except as provided in Sections 11B-403.5.2 and 11B-403.5.3, the clear width of walking surfaces shall be 36 inches (914 mm) minimum. Exceptions: 1. ...
-
Grab Bars
Grab bars and any wall or other surfaces adjacent to grab bars must have rounded edges and are not allowed to have sharp or abrasive surfaces....
-
11B-705.1.2.3 Islands or cut-through medians
cut-through less 2 inches (51 mm) maximum on each side, placed at the edges of the pedestrian island or cut-through median, and shall be separated by 24 inches (610 mm) minimum of walking surface...
-
404 Doors, Doorways, and Gates
series (404.2.6) clarify the height of door and gate hardware and add an exception for gates at pools, spas, and hot tubs (404.2.7) revise an exception for door and gate surface...
-
606.3 Height
Lavatories and sinks shall be installed with the front of the higher of the rim or counter surface 34 inches (865 mm) maximum above the finish floor or ground. EXCEPTIONS: 1....
-
Amusement Ride Seats Designed for Transfer
When greater distances are required for transfer, consideration should be given to providing gripping surfaces, seat paddings, and avoiding sharp or protruding objects....
-
1007.3.2 Golf Club Reach Range Area
This includes accessible routes provided adjacent to or, where provided, on the playing surface of the hole....
-
Tent Pads and Tent Platforms [1013]
Tent pads and tent platforms are defined spaces with prepared surfaces for setting up and securing tents....
-
F. Check-In Areas
If a permanent reception counter is used for check in, make sure to provide a writing surface at an accessible height for people who use a wheelchair, scooter, or other mobility device....
-
4.6.1 General
In alterations, where a condition for exception in section 1.1 prohibits full compliance with a specific requirement for clear floor or ground space surface, slope, size, or location, the...
-
2. Referenced Documents
Guide for Conducting Subjective Pavement Ride Quality Ratings E2133 Standard Test Method for Using a Rolling Inclinometer to Measure Longitudinal and Transverse Profiles of a Traveled Surface...
-
1013.1 General
Tent pads and tent platforms are defined spaces with prepared surfaces for setting up and securing tents....
-
§ 38.159(b)(7) Platform gaps
Any openings between the platform surface and the raised barriers shall not exceed 5/8 inch (16 mm) in width....
