EXCEPTIONS: 1. Sales counters and service counters shall not be required to comply with 902. 2....
Search Results "9-1-1 Service"
Filters
Commonly Searched Documents
-
226.1 General
-
General Accommodations
If these areas do not have escape routes, they should have 1) an operating phone, cell-phone, TTY, and two-way radio so that emergency services can be contacted; 2) a closing door; 3) supplies...
-
III. JURISDICTION
. § 12131(1)....
-
II. MODEL FACILITIES
installation, the model facilities will serve as laboratories for the development of effective policies, procedures, and programs to increase access and improve the delivery of health services...
-
2.1 Health Care Experiences of Persons with Disabilities
Preventive Services Task Force. ...
-
Mississippi Department of Rehabilitation Services (MDRS)
Overview of Services and Programs It is the mission of the Mississippi Department of Rehabilitation Services (MDRS), to provide appropriate and comprehensive services to Mississippians...
-
14. Who in a school district participates in the determinations about the provision of auxiliary aids and services under Title II? Does the ultimate decision maker differ depending upon whether the student is covered by the IDEA, Title II, or both?
The Title II regulations do not designate a particular responsible person or group of people to make the determinations about the provision of auxiliary aids and services under Title II....
-
706.2 Receiver Jacks
Receivers required for use with an assistive listening system shall include a 1/8 inch (3.2 mm) standard mono jack. [ECTCR UFAS 4.33.7]...
-
609.2.1 Circular Cross Section
Grab bars with circular cross sections shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
802.1.1 Floor or Ground Surface
EXCEPTION: Slopes not steeper than 1:48 shall be permitted....
-
M305.2.4.1 Circular Cross Section
Transfer supports with circular cross sections shall have an outside diameter of 1 ¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
M303.3.2 Beveled
Changes in level between ¼ inch (6.4 mm) high and ½ inch (13 mm) high maximum shall be beveled with a slope not steeper than 1:2....
-
802.1.1 Floor or Ground Surface
EXCEPTION: Slopes not steeper than 1:48 shall be permitted....
-
409.4.4 Leveling
Each car shall automatically stop at a floor landing within a of 1/2 inch (13 mm) under rated loading to zero loading conditions....
-
Individual captioning device (Section-by-Section Analysis)
In § 36.303(g)(1)(iv), the Department is proposing to define “individual captioning device” as “the individual device that patrons may use at their seats to view the closed captions.”...
-
T303.3.2 Handrail and Stanchion Circular Cross Section
Handrails and stanchions with a circular cross section shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (50 mm) maximum....
-
Figure 11B-407.2.3.1 Floor designation
Revises the braille designation on the figure to correctly indicate the number 1 and revises figure title....
-
706.2 Receiver Jacks
Receivers required for use with an assistive listening system shall include a 1/8 inch (3.2 mm) standard mono jack....
-
11B-609.2.1 Circular cross section
Grab bars with circular cross sections shall have an outside diameter of 1¼ inches (32 mm) minimum and 2 inches (51 mm) maximum....
-
Sec. 12164. Regulations. [Section 244]
Not later than 1 year after July 26, 1990, the Secretary of Transportation shall issue regulations, in an accessible format, necessary for carrying out this subpart....
-
505.5 Clearance
Clearance between handrail gripping surfaces and adjacent surfaces shall be 1½ inches (38 mm) minimum. Figure 505.5 Handrail Clearance...
-
407.4.3 Platform to Hoistway Clearance
The clearance between the car platform sill and the edge of any hoistway landing shall be 1¼ inch (32 mm) maximum....
-
12143(b) Issuance of regulations
(b) Issuance of regulations Not later than 1 year after July 26, 1990, the Secretary shall issue final regulations to carry out this section....
-
406.3 Sides of Curb Ramps
Where provided, curb ramp flares shall not be steeper than 1:10. Figure 406.3 Sides of Curb Ramps...
