Transfer supports shall comply with M305.2.1.1 or M305.2.1.2 and shall be located 1 ½ inches (38 mm) maximum measured horizontally from the plane defined by the nearest edge of the...
Search Results "Flared Side"
Filters
Commonly Searched Documents
-
M305.2.1 Location
-
M305.2.4 Cross Section
Transfer supports shall have a cross section complying with 305.2.4.1 or 305.2.4.2.
-
M305.2.3 Height
During use, the tops of transfer support gripping surfaces shall be 6 inches (150 mm) minimum and 19 inches (485 mm) maximum higher than the top of the associated uncompressed...
-
M305.2.6 Gripping Surfaces (Section-by-Section Analysis)
The proposed rule did not provide any specific requirements regarding gripping surfaces on transfer supports. However, in the MDE NPRM preamble the Access Board repeatedly noted that...
-
M305.2.4 Cross Section (Section-by-Section Analysis)
The proposed rule did not provide specific requirements for the cross section of transfer supports. However, in the MDE NPRM preamble, the Access Board noted that it was considering...
-
5.4.9 Interruptions along Transfer Support Gripping Recommendation for M301 and M302
5.4.9 Interruptions along Transfer Support Gripping Recommendation for M301 and M302 Description: Transfer supports may contain elements to provide structural support or prevent...
-
5.4.5 Transfer Support Position Recommendation for M301 and M302
5.4.5 Transfer Support Position Recommendation for M301 and M302 Description: Transfer support position refers to the placement of the gripping surface within the minimum and...
-
5.4.2 Transfer Support Length for M301 and M302
5.4.2 Transfer Support Length for M301 and M302 Description: Transfer support length applies to the gripping surface of the support, that portion of the support used to grasp or...
-
5.7.1 Lift Compatibility Clearance in Base for M301
5.7.1 Lift Compatibility Clearance in Base for M301 Description: For portable floor lifts to be effective, they must deploy at diagnostic equipment such that the boom of the lifts...
-
M305.2.1 Location
Transfer supports shall be located within reach of the transfer surface and shall not obstruct transfer onto or off of the surface when in position.
-
Brey-Krause Concealed Mounting Security / Anti Suicide Grab Bars
The concealed mount anti-ligature grab bars are fabricated from 18 gauge stainless steel. The flange is constructed from 11 gauge stainless steel and is three inches in diameter....
-
Behavioral Safety Products #GB350 Suicide Resistant Safety Grab Bar with Full Closure Plate
Product Description We offer this suicide resistant grab bar in seven lengths: 18", 24", 30", 32", 36", 42", and 48". All lengths except for the 18" and 32" are available for...
-
Is compliance on both sides of a door or gate required when it is usable only from one side?
No, compliance is not required on both sides of those doors or gates that can be used in one direction only. Compliance is required only on the usable side....
-
Comparison of Single-User Toilet Room “Pairs” With Fixtures Side-by-Side: Plan 2C
Comparison of Single-User Toilet Room “Pairs” With Fixtures Side-by-Side: Plan 2C 2010 Standards Plan-2C Pair: 2010 Standards with In-Swinging Doors...
-
T208.2.2 Doorways on Two Sides of vehicle
Where non-rail vehicles have doorways on two sides, a passenger access route shall connect each wheelchair space to doorways on both sides of the vehicle that provide a means of accessible...
-
DSA IR 16-12: GRAB BAR DESIGN AND CONNECTIONS: 2019 CBC
shall be established in the same manner. 2.3 As an alternate to Section 2.2 above for grab bars spanning 36” or less between supports, a connection using a back-up plate on the other side...
-
11B-705.1.2.2.1 Perpendicular curb ramps
Detectable warnings shall extend the full width of the ramp run less 2 inches (51 mm) maximum on each side, excluding any flared sides....
-
M301.2.1 Adjustability
Transfer surfaces shall be adjustable in height measured from the floor to the top of the uncompressed transfer surface and shall provide the following: A. A low transfer position...
-
M301.2.2 Sunset
The low transfer position height, Item A of M301.2.1, shall cease to have effect on [Insert date 5 years after date of publication in the Federal Register].
-
M301.2.2 Sunset Provision (Section-by-Section Analysis)
As discussed in Section IV.B.1.a. (Significant Changes – Transfer Surface Adjustability), this is a new provision that was added to the final rule in conjunction with the new...
-
The UpScale Medical Exam Table
Learn more at http://medicalaccessibility.com/ Two Products in One - Combines a height-adjustable exam table with an accessible weight scale to save money and save...
-
Stable and rock solid. See for yourself!
Learn more at http://medicalaccessibility.com/ Two Products in One - Combines a height-adjustable exam table with an accessible weight scale to save money and save...
-
Exam Tables & Scales: What Patients Say...
Hear from patients about their experiences accessing a comprehensive exam, transferring onto exam tables, and getting weighed. At Medical Accessibility, our mission is to help...
-
Appendix 3 - Comparison of US Standards to IDEA Center Research
Reach 1270 119 1597 1347 1704 Low Side Reach 380...
