(DOT ADA Standard 810.10.)...
Search Results "Applicable Standard"
-
Flange way gap
-
I1a
[ADA Standards § 4.31.2, Fig. 44 (a)] Yes No...
-
D4
[ADA Standards § 4.13.6, Fig. 25] Yes No If No, leave the door propped open or find another accessible entrance....
-
301.1 Scope
Chapter 3 shall apply to ICT where required by 508 Chapter 2 (Scoping Requirements), 255 Chapter 2 (Scoping Requirements), and where otherwise referenced in any other chapter of the 508 Standards...
-
4.17.4 Toe Clearances
In standard stalls, the front partition and at least one side partition shall provide a toe clearance of at least 9 in (230 mm) above the floor....
-
4.17.4 TOE CLEARANCES
In standard stalls, the front partition and at least one side partition shall provide a toe clearance of at least 9 in (230 mm) above the floor....
-
Stability or Stable Surface
stable surface is one that remains unchanged by contaminants or applied force, so that when the contaminant or force is removed, the surface returns to its original condition (2010 ADA Standards...
-
World Disability Union (WDU)
Our Goal Prevention of disability Equality of Opportunity Rehabilitation "lmprovement5" Universal Standards Our Values Pustice Affection Brotherhood Goodness Our Agenda...
-
§35.150 Existing facilities (Section-by-Section Analysis)
Congress intended the "undue burden" standard in title II to be significantly higher than the "readily achievable" standard in title III....
-
502.3.1 Object Information (Section-by-Section Analysis)
It is also consistent with existing 508 Standards § 1194.21(d), but more explicitly provides for the user to be able to change data values, not just read them....
-
502.2.1 User Control of Accessibility Features (Section-by-Section Analysis)
This provision would be new to the 508 Standards and 255 Guidelines, though it draws on the prohibition in § 1194.21(b) of the existing 508 Standards against disrupting or disabling accessibility...
-
Accessible Routes in Dwelling Units with Mobility Features
The 2010 Standards at sections 233.3.1.1, 809.1, 809.2, 809.2.1, and 809.4 will require all spaces and elements within dwelling units with mobility features to be on an accessible route....
-
Registered Accessibility Specialist (RAS) Bulletin RAS 2014-04 Signs - Exit Doors
However, a RAS has no authority to require compliance with TAS 216.4.1 based on RAS Bulletin 2012-01 since a referenced standard (ICC/IBC) dictates the location of exit passageway, exit...
-
5.7.1.1 Lift Compatibility Clearance in Base for Stretchers (M301)
The change harmonizes this provision with the international standards. IEC 60601-2-52 provides requirements for stretchers and includes a lift clearance at the 39 inch width....
-
Facility
Facilities must comply with all 2010 ADA Standards for Accessible Design for new construction and remodeling projects....
-
Door Hardware
The ANSI standard also recognizes this point....
-
12101(b)(4)
L. 110-325, § 2, Sept. 25, 2008, 122 Stat. 3553, provided that: (4) to reject the standards enunciated by the Supreme Court in Toyota Motor Manufacturing, Kentucky, Inc. v....
-
407.12.3 Forward Reach (Section-by-Section Analysis)
As noted previously, the existing 508 Standards do not provide specifications for forward reaches....
-
C102.5 IETF
Copies of the referenced standard may be obtained from the Internet Engineering Task Force (http://www.ietf.org)....
-
210 Stairways
1991 Standards for Accessible Design 2010 Standards for Accessible Design What’s New/Different 4.1.3(4) Interior...
-
3.3.15.3 Side (lateral) reach – over an obstruction depth of 610 mm
For heights that approximated the U.S. standard of 1170 mm (46 in.), only 31% of the manual wheelchair users, 24% of the power wheelchair users and 13% of the scooter users could reach 610...
-
State or Local Code Certification
The ADA sets up a voluntary process through which a state code can be certified by DOJ as meeting or exceeding the ADA Standards that apply to public accommodations and commercial facilities...
-
Are freight or service elevators required to comply?
Where provided, they must comply with the Standards....
-
§ 35.151(k)(2) Alterations to detention and correctional facilities.
Alterations to jails, prisons, and other detention and correctional facilities shall comply with the 2010 Standards except that public entities shall provide accessible mobility features...
