The rear edge of an L-shaped seat shall be 2½ inches (64 mm) maximum and the front edge 15 inches (381 mm) minimum and 16 inches (406 mm) maximum from the seat wall....
Search Results "Shall"
-
11B-610.3.2 L-shaped seats
-
Sec.36.603(d)
(d) The submitting official shall file the original and one copy of the request and of supporting materials with the Assistant Attorney General....
-
608.5.3 Alternate Roll-In Type Shower Compartments
In alternate roll-in type shower compartments, the controls, faucets, and shower spray unit shall be located above the grab bar, but no higher than 48 inches (1220 mm) above the shower floor...
-
308.3.1 Unobstructed
Where a clear floor or ground space allows a parallel approach to an element and the side reach is unobstructed, the high side reach shall be 48 inches (1220 mm) maximum and the low side...
-
4.1.2(6)
(6) If toilet facilities are provided on a site, then each such public or common use toilet facility shall comply with 4.22....
-
308.3.1 Unobstructed
Where a clear floor or ground space allows a parallel approach to an element and the side reach is unobstructed, the high side reach shall be 48 inches (1220 mm) maximum and the low side...
-
11B-308.3.1 Unobstructed
Where a clear floor or ground space allows a parallel approach to an element and the side reach is unobstructed, the high side reach shall be 48 inches (1219 mm) maximum and the low side...
-
11B-610.3.2 L-shaped seats
The rear edge of an L-shaped seat shall be 2½ inches (64 mm) maximum and the front edge 15 inches (381 mm) minimum and 16 inches (406 mm) maximum from the seat wall....
-
11B-810.6.2 Routes and destinations
Lists of stations, routes and destinations served by the station which are located on boarding areas, platforms, or mezzanines shall comply with Section 11B-703.5 _|Signs; Visual Characters...
-
11B-806.2.4 Toilet and bathing facilities
At least one bathroom that is provided as part of a guest room shall comply with Section 11B-603....
-
11B-805.2.4 Toilet and bathing rooms
Where provided, one water closet, one lavatory, and one bathtub or shower shall comply with the applicable requirements of Sections 11B-603 through 11B-610....
-
11B-805.2.4 Toilet and bathing rooms
Where provided, one water closet, one lavatory, and one bathtub or shower shall comply with the applicable requirements of Sections 11B-603 through 11B-610....
-
11B-806.2.4 Toilet and bathing facilities
At least one bathroom that is provided as part of a guest room shall comply with Section 11B-603....
-
REPORTING AND ENFORCEMENT
This Agreement shall become effective as of the date of the last signature below (“Effective Date”) and shall remain in effect for four (4) years from that date....
-
§ 382.41 Stowage of personal equipment
(4) Carriers shall not drain batteries....
-
IV. ALTERATIONS AND NEW CONSTRUCTION
Thereafter, the ILA shall inspect the Events Center every two (2) months to determine whether the construction of the Events Center is in compliance with the ADA Plans and shall report the...
-
1134A.6, Item 4
Grab bar reinforcement shall be installed continuous in the walls of showers 32 inches to 38 inches (813 mm to 965 mm) above the floor....
-
404.3 Automatic and Power-Assisted Doors and Gates
Automatic doors and automatic gates shall comply with 404.3....
-
11B-703.7.2.6.1 Men’s toilet and bathing facilities
Men’s toilet and bathing facilities shall be identified by an equilateral triangle, ¼ inch (6.4 mm) thick with edges 12 inches (305 mm) long and a vertex pointing upward....
-
1009.5.2 Transfer Space
A transfer space of 60 inches (1525 mm) minimum by 60 inches (1525 mm) minimum with a slope not steeper than 1:48 shall be provided at the base of the transfer platform surface and shall...
-
216.5 Parking
Parking spaces complying with 502 shall be identified by signs complying with 502.6. EXCEPTIONS: 1....
-
11B-502.1 General
Car and van parking spaces shall comply with Section 11B-502....
-
804.2 Clearance
Where a pass through kitchen is provided, clearances shall comply with 804.2.1. Where a U-shaped kitchen is provided, clearances shall comply with 804.2.2....
-
11B-404.2.5 Thresholds
Thresholds, if provided at doorways, shall be ½ inch (12.7 mm) high maximum. Raised thresholds and changes in level at doorways shall comply with Sections 11B-302 and 11B-303....