None of the research identified described how well individuals are able to overcome physical barriers in between the wheelchair and target surfaces. ...
Search Results "Ramp Surface"
Filters
Commonly Searched Documents
-
Expert opinion on the current knowledge
-
11B-403.5.1 Clear width
Except as provided in Sections 11B-403.5.2 and 11B-403.5.3, the clear width of walking surfaces shall be 36 inches (914 mm) minimum. Exceptions: 1. ...
-
Grab Bars
Grab bars and any wall or other surfaces adjacent to grab bars must have rounded edges and are not allowed to have sharp or abrasive surfaces....
-
11B-705.1.2.3 Islands or cut-through medians
cut-through less 2 inches (51 mm) maximum on each side, placed at the edges of the pedestrian island or cut-through median, and shall be separated by 24 inches (610 mm) minimum of walking surface...
-
404 Doors, Doorways, and Gates
series (404.2.6) clarify the height of door and gate hardware and add an exception for gates at pools, spas, and hot tubs (404.2.7) revise an exception for door and gate surface...
-
606.3 Height
Lavatories and sinks shall be installed with the front of the higher of the rim or counter surface 34 inches (865 mm) maximum above the finish floor or ground. EXCEPTIONS: 1....
-
Amusement Ride Seats Designed for Transfer
When greater distances are required for transfer, consideration should be given to providing gripping surfaces, seat paddings, and avoiding sharp or protruding objects....
-
1007.3.2 Golf Club Reach Range Area
This includes accessible routes provided adjacent to or, where provided, on the playing surface of the hole....
-
Tent Pads and Tent Platforms [1013]
Tent pads and tent platforms are defined spaces with prepared surfaces for setting up and securing tents....
-
F. Check-In Areas
If a permanent reception counter is used for check in, make sure to provide a writing surface at an accessible height for people who use a wheelchair, scooter, or other mobility device....
-
4.6.1 General
In alterations, where a condition for exception in section 1.1 prohibits full compliance with a specific requirement for clear floor or ground space surface, slope, size, or location, the...
-
2. Referenced Documents
Guide for Conducting Subjective Pavement Ride Quality Ratings E2133 Standard Test Method for Using a Rolling Inclinometer to Measure Longitudinal and Transverse Profiles of a Traveled Surface...
-
1013.1 General
Tent pads and tent platforms are defined spaces with prepared surfaces for setting up and securing tents....
-
§ 38.159(b)(7) Platform gaps
Any openings between the platform surface and the raised barriers shall not exceed 5/8 inch (16 mm) in width....
-
11B-1007.3.2 Golf club reach range area
This includes accessible routes provided adjacent to or, where provided, on the playing surface of the hole. ...
-
11B-1007.3.2 Golf club reach range area
This includes accessible routes provided adjacent to or, where provided, on the playing surface of the hole. ◼ ...
-
11B-308.3.1 Unobstructed
Operable parts of fuel dispensers shall be permitted to be 54 inches (1372 mm) maximum measured from the surface of the vehicular way where fuel dispensers are installed on existing curbs...
-
11B-705.1.2.3 Islands or cut-through medians
cut-through less 2 inches (51 mm) maximum on each side, placed at the edges of the pedestrian island or cut-through median, and shall be separated by 24 inches (610 mm) minimum of walking surface...
-
Bradley 20.6 Gallon Waste Receptacle 355
Model 355 Surface Mounted 20.6 Gallon Capacity Surface Mounted...
-
Function Keys
It included specifications for key surfaces to be raised 1/25 inch minimum and that outer edges have a radius of 1/50 inch maximum (707.4.2)....
-
Step 2: Identify the Presence of Limiting Factors
What sort of surface is firm and stable? If the answer to both of the following questions is yes, the surface is probably firm and stable....
-
Stanley FBB 269 Heavy Weight Ball Bearing “Swing Clear” Offset Door Hinge
clear 90° Equipped with four Stanley permanently lubricated non-detachable ball bearings Pins in nonferrous hinges are stainless steel Heavy weight gauges increase available bearing surface...
-
Stanley FBB 266 Heavy Weight Ball Bearing “Swing Clear” Offset Door Hinge
clear 90° Equipped with four Stanley permanently lubricated non-detachable ball bearings Pins in nonferrous hinges are stainless steel Heavy weight gauges increase available bearing surface...
-
Stanley FBB 268 Heavy Weight Ball Bearing “Swing Clear” Offset Door Hinge
clear 90° Equipped with four Stanley permanently lubricated non-detachable ball bearings Pins in nonferrous hinges are stainless steel Heavy weight gauges increase available bearing surface...
