The floor or ground surface of the ramp run or landing shall extend 12 inches (305 mm) minimum beyond the inside face of a handrail complying with 505....
Search Results "Practice Teeing Ground"
-
405.9.1 Extended Floor or Ground Surface
-
11B-1007.3.1 Start of play
A clear floor or ground space 48 inches (1219 mm) minimum by 60 inches (1524 mm) minimum with slopes not steeper than 1:48 shall be provided at the start of play....
-
Start of Play: ADA Standard Section 1007.3.1
A clear floor or ground space 48 inches (1220 mm) minimum by 60 inches (1525 mm) minimum with slopes not steeper than 1:48 shall be provided at the start of play....
-
11B-1007.3.1 Start of play
A clear floor or ground space 48 inches (1219 mm) minimum by 60 inches (1524 mm) minimum with slopes not steeper than 1:48 shall be provided at the start of play....
-
1008.2.6.1 Accessibility
Ground surfaces shall comply with ASTM F 1951 (incorporated by reference, see "Referenced Standards" in Chapter 1)....
-
AccessRec DuraDeck 2 Molded Plastic Mat Ground Surface
Sections are engineered to provide ground protection and access over soft surfaces and will provide a firm support base and traction for numerous activities....
-
11B-1005.3.2 Extended ground or deck surface
The ground or deck surface shall extend 12 inches (305 mm) minimum beyond the inside face of the railing....
-
11B-1005.3.2 Extended ground or deck surface
The ground or deck surface shall extend 12 inches (305 mm) minimum beyond the inside face of the railing....
-
11B-1005.4 Clear floor or ground space
At each location where there are railings, guards, or handrails complying with Section 11B-1005.2.1, a clear floor or ground space complying with Section 11B-305 shall be provided....
-
11B-1005.4 Clear floor or ground space
At each location where there are railings, guards, or handrails complying with Section 11B-1005.2.1, a clear floor or ground space complying with Section 11B-305 shall be provided....
-
11B-1005.4 Clear floor or ground space
At each location where there are railings, guards, or handrails complying with Section 11B-1005.2.1, a clear floor or ground space complying with Section 11B-305 shall be provided....
-
§35.130(a) (Section-by-Section Analysis)
Paragraph (a) restates the nondiscrimination mandate of section 202 of the ADA. The remaining paragraphs in §35.130 establish the general principles for analyzing whether any...
-
§35.130(a)
(a) No qualified individual with a disability shall, on the basis of disability, be excluded from participation in or be denied the benefits of the services, programs, or activities...
-
§100.80(b)
(b) Prohibited actions under this section include, but are not limited to:
-
§100.5 Scope.
[See subsections ...]
-
2.2.1
List all applicable industry standards that define tolerances and measurement protocols, if any.
-
§ 37.43(f)(1)
(1) When the cost of alterations necessary to make a path of travel to the altered area fully accessible is disproportionate to the cost of the overall alteration, then such areas...
-
1011.2.2 Surface
This section requires the surface of the clear ground space to be firm and stable....
-
3. Study Findings
[See subsections ...]
-
CONCLUSIONS
CONCLUSIONS The results of this pilot study suggest: • Surfaces that can be objectively measured as firm and stable generally require less energy, are perceived as less...
-
Accessible Exterior Surfaces
Accessible Exterior Surfaces This is an executive summary of the “Accessible Exterior Surfaces Technical Report” dated 24 April 1999. This report is available through the Access...
-
Accessible Exterior Surfaces Technical Article
Accessible Exterior Surfaces Technical Article Submitted by: Peter W. Axelson, M.S.M.E., A.T.P. Project Director Denise Chesney, M.E.B.M.E. Research Coordinator Beneficial...
-
RESULTS OF OBJECTIVE SURFACE MEASUREMENT
RESULTS OF OBJECTIVE SURFACE MEASUREMENT Wheelchair Work Measurements. The work required to propel a wheelchair in a straight path provided an indication of the firmness of the...
-
RECOMMENDATIONS
RECOMMENDATIONS An objective test procedure for measuring the firmness and stability of surfaces with a portable device and performance specifications need to be accepted in order...
