Section 105.2.2 of the ADA Standards cover references to the American Society of Mechanical Engineers (ASME) standards.
Search Results "Transfer Surface Height"
-
ASME: ADA Standard Section 105.2.2
-
EZ-ACCESS Transitions® Angled Entry Ramp
Entry Ramp – is a portable, stand-alone threshold ramp featuring independently adjustable legs with swivel feet, allowing for vertical adjustment ranging from 1-3/8 to 5-7/8 inches in height...
-
11B-407.4.10.1 Location
Clearance between support rails and adjacent surfaces shall be 1½ inches (38 mm) minimum....
-
11B-407.4.10.1 Location
Clearance between support rails and adjacent surfaces shall be 1½ inches (38 mm) minimum....
-
Zurn Insulation Combination Kit: One Trap Protector, Two Stop Supply Protectors and One Offset Drain Protector
Protector, Two Stop Supply Protectors and One Offset Drain Protector FEATURES: Satin white PVC resin 3/8" Nominal wall with vandal resistant clips ADA compliant and resists thermal transfer...
-
Detectable Warning
A standardized surface feature built in or applied to walking surfaces or other elements to warn visually impaired people of hazards on a circulation path....
-
TACTILE WARNING
A standardized surface texture applied to or built into walking surfaces or other elements to warn visually impaired people of hazards in the path of travel....
-
StaLok
During the testing performed in August 2007, it was noted that an individual had walked on the surface at the Wetlands dedication and left marks in the surface of a depth of approximately...
-
306.3.4 Clearance Reduction
inches (230 mm) and 27 inches (685 mm) above the finish floor or ground, the knee clearance shall be permitted to reduce at a rate of 1 inch (25 mm) in depth for each 6 inches (150 mm) in height...
-
Introduction
Footrest clearance height and depth...
-
306.3.4 Clearance Reduction
inches (230 mm) and 27 inches (685 mm) above the finish floor or ground, the knee clearance shall be permitted to reduce at a rate of 1 inch (25 mm) in depth for each 6 inches (150 mm) in height...
-
306.3.4 Clearance Reduction
inches (230 mm) and 27 inches (685 mm) above the finish floor or ground, the knee clearance shall be permitted to reduce at a rate of 1 inch (25 mm) in depth for each 6 inches (150 mm) in height...
-
11B-703.5.8 Character spacing
Spacing between individual characters shall be 10 percent minimum and 35 percent maximum of character height....
-
306.3.4 Clearance Reduction
inches (230 mm) and 27 inches (685 mm) above the finish floor or ground, the knee clearance shall be permitted to reduce at a rate of 1 inch (25 mm) in depth for each 6 inches (150 mm) in height...
-
§382.57(c)(6)(i) Input controls
Where provided, key surfaces not on active areas of display screens, must be raised above surrounding surfaces....
-
Recommendations
Recommendations Based on the data in Table 1 and the observations above, we recommend: a minimum flat surface of 40 in. length for platforms accommodating wheeled mobility devices...
-
§27.71(k)(6)(i) Input controls.
Where provided, key surfaces not on active areas of display screens, must be raised above surrounding surfaces....
-
§ 382.57(c)(6)(i) Input controls
Where provided, key surfaces not on active areas of display screens, must be raised above surrounding surfaces....
-
§ 27.71(k)(6)(i) Input controls
Where provided, key surfaces not on active areas of display screens, must be raised above surrounding surfaces....
-
HEWI Polymide Pull Handles
They are designed to enable a variable gripping height from 75 to 120 cm. They are therefore equally suitable for wheelchair and rollator users....
-
CalCasp Training: Advanced Scoping
This course will provide a series of scenarios and/or situations that are complex and not as easy as looking up the height of a grab bar in the code book....
-
604.9 Water Closets and Toilet Compartments for Children’s Use
Water Closet Centerline 12 inches (305 mm) 12 to 15 inches(305 to 380 mm) 15 to 18 inches(380 to 455 mm) Toilet Seat Height...
-
703 Signs
Requirements for signs provide specifications for raised characters (703.2), braille characters (703.3), the height and location of signs with tactile characters (703.4), visual characters...
-
3.3.15.1 Forward reach – unobstructed
Lower percentages in a forward reach for scooter users partially resulted from having to overcome a greater distance to reach over and/or around the front tiller, particularly at lower heights...
