Only approved DSA-AC detectable warning products and directional surfaces shall be installed as provided in the California Code of Regulations (CCR), Title 24, Part 1, Chapter 5, Articles...
Search Results "Transfer Surface Height"
Filters
Commonly Searched Documents
-
11B-705.3 Product Approval
-
Foot-candle
The illumination on a surface one square foot in area on which there is a uniformly distributed flux of one lumen, or the illuminance produced on a surface all points of which are at a distance...
-
Edge Protection [§405.9]
Edge Protection [§405.9] Edge protection along ramp runs and landings keep wheelchair casters and crutch tips on the surface and can be provided by curbs, barriers, or extended surfaces...
-
2.3.2
For example, floor profilers can provide a very accurate measurement of surface flatness but are expensive and require training to use....
-
11B-705.3 Product Approval
Only approved DSA-AC detectable warning products and directional surfaces shall be installed as provided in the California Code of Regulations (CCR), Title 24, Part 1, Chapter 5, Articles...
-
11B-403.5.1 Clear width
Except as provided in Sections 11B-403.5.2 and 11B-403.5.3, the clear width of walking surfaces shall be 36 inches (914 mm) minimum....
-
Questionnaire Data
Table 7 displays the results from the surface questionnaire for all surfaces....
-
11B-602.9 Pedestrian protection
When used, wing walls or barriers shall project horizontally at least as far as the drinking fountain and to within 6 inches (152 mm) vertically from the floor or ground surface....
-
AJW Architectural Products UG120-Railing UG120X-Y108 108" Exposed Flange, 1.25" Diameter, Peened Grip - Configuration Y
Recommended mounting heights for grab bars are 33" - 36" centerline above finished floor. All mounting of grab bars when possible should have in wall mounting back plates....
-
AJW Architectural Products UG130-Railing UG130X-Y108 108" Exposed Flange, 1.5" Diameter Grab Bar, Peened Grip - Configuration Y
Recommended mounting heights for grab bars are 33" - 36" centerline above finished floor. All mounting of grab bars when possible should have in wall mounting back plates....
-
AJW Architectural Products UG3-Railing UG3X-Y108 108" Concealed Snap Flange, 1.5" Diameter, Peened Grip - Configuration Y
Recommended mounting heights for grab bars are 33" - 36" centerline above finished floor. All mounting of grab bars when possible should have in wall mounting back plates....
-
Manual vs. Power (Questionnaire Data)
It should be noted that even though manual WC users had higher vibrations for all engineered surfaces, on average they rated all surfaces better than power chair users....
-
Do basements count in determining a facility’s story count?
As defined in the Standards, a “story” pertains to those portions of buildings “designed for human occupancy included between the upper surface of a floor and upper surface of the floor...
-
DETECTABLE WARNING
A standardized surface feature built in or applied to walking surfaces or other elements to warn of hazards on a circulation path. Advisory Definition of DETECTABLE WARNING....
-
1132A.4.1 Thresholds
Changes in height at interior door thresholds (e.g., floor material changes at door thresholds) shall not exceed ½ inch (12.7 mm). Thresholds shall comply with the following:...
-
607 Bathtubs
Changes made to this section include: revision of grab bar mounting heights (607.4) integration of provisions for grab bars specific to residential dwelling units that were...
-
4.31.2 CLEAR FLOOR OR GROUND SPACE
Figure 44 Mounting Heights and Clearances for Telephones...
-
11B-605.4 Flush controls
Hand operated flush controls shall comply with Section 11B-309 except that the flush control shall be mounted at a maximum height of 44 inches (1118 mm) above the finish floor....
-
COMPARISON OF OBJECTIVE MEASURES AND ENERGY COSTS
COMPARISON OF OBJECTIVE MEASURES AND ENERGY COSTS Objective measures of surface firmness and stability were compared to energy costs (energy consumption, velocity, RPE and level of difficulty...
-
11B-809.9.2 Clear width
Kitchens shall have a minimum clear width measured between any cabinet, work surface or the face of any appliance (excluding handles and controls) and the opposing cabinet, work surface,...
-
¾ Inch Minus Limestone
After the same two days of uncharacteristically heavy rainfall (as noted in the ¼ inch minus segment), the surface had evidence of water pooling on the surface, as there were lines of pine...
-
4.3.6 Reach Limits
With weights that weigh more than 56 grams (2 oz.), we found that 20‒25% of all three WhMD users could not reach to the same heights as to the no-weight condition....
-
Zurn Model Z5560 Commercial EcoVantage ADA Height Elongated Toilet: Pressure-Assist Replacement Tank Kit Video
Requires the Registered User plan or above. Login! -
DETECTABLE WARNING
A standardized surface feature built in or applied to walking surfaces or other elements to warn of hazards on a circulation path. Advisory Definition of DETECTABLE WARNING. ...
