[ADA Standards § 4.7.2] Yes No Note: 1:12 is one inch of vertical height for 12 inches of horizontal distance....
Search Results "Transfer Surface Height"
-
e-ii
-
11B-703.5.8 Character spacing
Spacing between individual characters shall be 10 percent minimum and 35 percent maximum of character height....
-
R208.2 Where Not Required
Detectable warning surfaces are not required at pedestrian refuge islands that are cut-through at street level and are less than 1.8 meters (6.0 ft) in length in the direction of pedestrian...
-
Summary of Results
Therefore, the results can be addressed in terms of a general trend in types of surface materials used....
-
Handrails
Handrails must comply with the following: Clearance between handrail gripping surfaces and adjacent surfaces shall be 1 1/2 inches (38 mm) minimum. ...
-
406.2 Counter Slope
Counter slopes of adjoining gutters and road surfaces immediately adjacent to the curb ramp shall not be steeper than 1:20....
-
707.6.3.1 Contrast
Function keys shall contrast visually from background surfaces. Characters and symbols on key surfaces shall contrast visually from key surfaces....
-
11B-503.3.3 Marking
The area within the borderlines shall be marked with hatched lines a maximum of 36 inches (914 mm) on center in a color contrasting with that of the aisle surface....
-
11B-503.3.3 Marking
The area within the borderlines shall be marked with hatched lines a maximum of 36 inches (914 mm) on center in a color contrasting with that of the aisle surface....
-
Accessible Means for Gathering Feedback
., the desk must be on an accessible route and have a writing surface at the required height or a clipboard available for people who use wheelchairs)....
-
Back Support
The proposed rule required back support to be provided that extends vertically from a point no more than 2 inches above the bench to a height of at least 18 inches above the bench and that...
-
Mobility
Typical problems include maneuvering through narrow spaces, going up or down steep paths, moving over rough or uneven surfaces, using toilet and bathing facilities, reaching and seeing items...
-
Connections [1018.2]
Whenever possible, providing a beach access route that extends into the water will allow people to remain in their mobility devices and to transfer directly into the water....
-
2. Roll-in Shower Size
more than 50 guestrooms/suites, are all required roll-in showers at least 30" wide by 60" long or 36" wide by 60", as configured in Figure 57 below, so persons who use wheelchairs may transfer...
-
Size and Clearances [4.21.2]
Recommendation: Twelve inches of additional clear floor space at the seat will facilitate side transfers....
-
T303.4 Clearance
Clearance between gripping surfaces and adjacent surfaces shall be 1½ inches (38 mm) minimum....
-
4.34.6.4(5)
(5) There shall be no sharp or abrasive surfaces under such counters. Figure 50 Counter Work Surface...
-
11B-707.6.1 Input controls
Where provided, key surfaces not on active areas of display screens, shall be raised above surrounding surfaces....
-
707.6.1 Input Controls
Where provided, key surfaces not on active areas of display screens, shall be raised above surrounding surfaces....
-
707.6.1 Input Controls
Where provided, key surfaces not on active areas of display screens, shall be raised above surrounding surfaces....
-
11B-707.6.1 Input controls
Where provided, key surfaces not on active areas of display screens, shall be raised above surrounding surfaces....
- HEWI Polymide Pull Handles
-
11B-203.6 Single occupant structures
Single occupant structures accessed only by passageways below grade or elevated above standard curb height, including but not limited to, toll booths that are accessed only by underground...
-
F203.7 Single Occupant Structures
Single occupant structures accessed only by passageways below grade or elevated above standard curb height, including but not limited to, toll booths that are accessed only by underground...