[HCD 1 & HCD 2] See "Recommend."...
Search Results "9-1-1 Service"
Filters
Commonly Searched Documents
-
SHOULD
-
L-Shaped Seats: ADA Standard Section 610.3.2
Section 610.3.2 covers the current ADA Standards for L-shaped shower compartment seats.
-
Edge Protection: ADA Standard Section 405.9
Section 405.9 covers the current ADA Standards for edge protection at ramps.
-
11B-610.3.2 L-shaped seats
The rear edge of the “L” portion of the seat shall be 1½ inches (38 mm) maximum from the wall and the front edge shall be 14 inches (356 mm) minimum and 15 inches (381 mm) maximum from the...
-
11B-1005.2.1 Height
International Building Code (2000 edition) or sections 1012.2 and 1012.3 of the International Building Code (2003 edition) (incorporated by reference, see "Referenced Standards" in Chapter 1)...
-
11B-406.5.3 Landings
The slope of the landing in all directions shall be 1:48 maximum. [2010 ADA Standards] 406.4 Landings. Landings shall be provided at the tops of curb ramps....
-
Section D: Entrances
(§404.2.4) D4 Is the area in front of the door level, with slopes no greater than 1:48 in all directions?...
-
Gangway Slope and Rise Exceptions
Gangway Slope and Rise Exceptions Gangways must be designed to provide for a maximum 1:12 (8.33%) slope but are not required to be longer than 30 feet in length....
-
B. Slopes
.: in the direction of travel) not more than 1:20 (critical dimension of 1 1/4" or less)?...
-
11B-406.5.3 Landings
The slope of the landing in all directions shall be 1:48 maximum. Exception: Parallel curb ramps shall not be required to comply with Section 11B-406.5.3....
-
11B-233.3.1.2.6.1 Single building with one common (lobby) entrance
floor units in non-elevator buildings shall be adaptable and on an accessible route unless an accessible route to the common (lobby) entrance is not required as determined by Test No. 1,...
-
The National Service Inclusion Project
The National Service Inclusion Project (NSIP), a training and technical assistance provider, is here to meet all of your training and technical assistance needs on the inclusion of individuals...
-
1002.2 Accessible Routes
EXCEPTIONS: 1....
-
11B-703.2.7 Character spacing
Where characters have rectangular cross sections, spacing between individual raised characters shall be 1/8 inch (3.2 mm) minimum and 4 times the raised character stroke width maximum....
-
703.3.1 Dimensions and Capitalization
Range Minimum in Inches Maximum in Inches Dot base diameter 0.059 (1.5 mm) to 0.063 (1.6 mm) Distance between two dots in the same cell 1...
-
1002.2 Accessible Routes
EXCEPTIONS: 1....
-
1002.2 Accessible Routes
EXCEPTIONS: 1....
-
1.2.6
Allowing a small percentage of localized slopes to exceed 8.3% is based on the allowable slopes in ADA/ABA - AG (2004) for existing buildings of 1:8 (12.5%) for maximum rises of 3 inches...
-
Changes in Level at Entry to Wheelchair Spaces (M303.3)
Level changes between ¼ inch high and ½ inch high would be required to be beveled with a slope not steeper than 1:2....
-
Alabama Radio Reading Service
LISTEN to the Alabama Radio Reading Service online: HERE Since 1978, the Alabama Radio Reading Service (ARRS) has served North Central Alabama’s blind and print-impaired community from...
-
11B-213.3 Plumbing fixtures and accessories
The 2013 California Plumbing Code (CPC), Table 4-1 provides minimum plumbing fixture requirements for new buildings, and changes of occupancy or use in an existing building resulting in...
-
1005.1 Accessible Routes
EXCEPTIONS: 1. Accessible routes serving floating fishing piers and platforms shall be permitted to use Exceptions 1, 2, 5, 6, 7 and 8 in 1003.2.1. 2....
-
5.8.2.7 Base Support Allowance
Base supports can be a maximum of 1½ inches high....
-
Floor [1014.3]
When the floor surface is constructed of asphalt, concrete, or boards, the slope of the floor surface must be no steeper than 1:48 (2 percent) in any direction, regardless of the type of...
