The accessible route shall connect ground level play components required to comply with Section 11B-240.2.1 and elevated play components required to comply with Section 11B-240.2.2, including...
Search Results "Signal Level"
-
11B-206.2.17.1 Ground level and elevated play components
-
11B-206.2.17.1 Ground level and elevated play components
The accessible route shall connect ground level play components required to comply with Section 11B-240.2.1 and elevated play components required to comply with Section 11B-240.2.2, including...
-
Accessible Sidewalks 3: Pedestrians with Low Vision
Requires the Registered User plan or above. Login! -
11B-504.4 Tread surface
Changes in level are not permitted. Exception: Treads shall be permitted to have a slope not steeper than 1:48....
-
11B-504.4 Tread surface
Changes in level are not permitted. Exception: Treads shall be permitted to have a slope not steeper than 1:48....
-
ElectionSource Wall Mounted Wireless Alert Assist
Wireless door bell attaches to wall and assists voters for entering voting precincts and entrances. 100 foot range.
-
11B-305.2 Floor or ground surfaces
Changes in level, slopes exceeding 1:48, and detectable warnings shall not be permitted. Exception: Reserved....
-
11B-305.2 Floor or ground surfaces
Changes in level, slopes exceeding 1:48, and detectable warnings shall not be permitted. Exception: Reserved....
-
1132A.4, Item 1
Changes in level shall comply with Section 1131A....
-
1132A.4, Item 1
Changes in level shall comply with Section 1131A....
-
Floor and Ground Surfaces: ADA Standard Section 503.4
Section 503.4 covers the current ADA Standards for the floor and ground surfaces at passenger loading zones.
-
1131A.2 Changes greater than ½ inch
Changes in level greater than ½ inch (12.7 mm) shall be made by means of a sloped surface not greater than 1 unit vertical in 20 units horizontal (5-percent slope), or a ramp, elevator or...
-
1131A.2 Changes greater than ½ inch
Changes in level greater than ½ inch (12.7 mm) shall be made by means of a sloped surface not greater than 1 unit vertical in 20 units horizontal (5-percent slope), or a ramp, elevator or...
-
504.4 Tread Surface
Changes in level are not permitted. EXCEPTION: Treads shall be permitted to have a slope not steeper than 1:48. Advisory 504.4 Tread Surface....
-
§ 38.83(c)(3) Ramp threshold
Changes in level between 1/4 inch and 1/2 inch shall be beveled with a slope no greater than 1:2....
-
504.4 Tread Surface
Changes in level are not permitted. EXCEPTION: Treads shall be permitted to have a slope not steeper than 1:48. Advisory 504.4 Tread Surface....
-
§ 38.159(c)(3) Ramp threshold
Changes in level between 1/4 inch (6.5 mm) and 1/2 inch (13 mm) shall be beveled with a slope no greater than 1:2....
-
1131A.2 Changes greater than ½ inch
Changes in level greater than ½ inch (12.7 mm) shall be made by means of a sloped surface not greater than 1 unit vertical in 20 units horizontal (5-percent slope), or a ramp, elevator or...
-
504.4 Tread Surface
Changes in level are not permitted. EXCEPTION: Treads shall be permitted to have a slope not steeper than 1:48. Advisory 504.4 Tread Surface....
-
7.4.6 Tread Obstacles
Tread obstacles on trails shall not exceed 2 inches (50 mm) in height measured vertically to the highest point. Where the trail surface is paved or is elevated above the natural...
-
Wet Conditions [§405.10]
Wet Conditions [§405.10] Landings subject to wet conditions must be designed to prevent the accumulation of water. Landings are permitted slopes not steeper than 1:48 to allow for...
-
Existing Elevators (Alterations)
Alterations made to an existing car also must be made to each elevator programmed to respond to the same hall call so that a consistent level of accessibility within banks is maintained....
-
Contact Mat (BE9026)
When somebody steps on the Contact Mat, it triggers the connected Visit transmitter, and the transmitter sends signals to the Visit receiver to alert the user....
-
Pushbutton Transmitter (BE1240)
When somebody presses the Pushbutton Transmitter, it sends a radio signal to the Visit receiver(s) for alerting. Choose how to be alerted from flashes, sounds and vibrations....
