Pemko manufactures thresholds in several materials to meet customer needs. Extruded Aluminum thresholds are manufactured of tempered aluminum, 6063-T6. Architectural bronze/brass...
Search Results "Signal Level"
Filters
Commonly Searched Documents
-
PEMKO 3" Floor Plates/Safety Treads No. 19125
-
11B-504.4 Tread surface
Changes in level are not permitted. Exception: Treads shall be permitted to have a slope not steeper than 1:48....
-
11B-504.4 Tread surface
Changes in level are not permitted. Exception: Treads shall be permitted to have a slope not steeper than 1:48....
-
11B-305.2 Floor or ground surfaces
Changes in level, slopes exceeding 1:48, and detectable warnings shall not be permitted. Exception: Reserved....
-
1132A.4, Item 1
Changes in level shall comply with Section 1131A....
-
1132A.4, Item 1
Changes in level shall comply with Section 1131A....
-
Floor and Ground Surfaces: ADA Standard Section 503.4
Section 503.4 covers the current ADA Standards for the floor and ground surfaces at passenger loading zones.
-
1131A.2 Changes greater than ½ inch
Changes in level greater than ½ inch (12.7 mm) shall be made by means of a sloped surface not greater than 1 unit vertical in 20 units horizontal (5-percent slope), or a ramp, elevator or...
-
1131A.2 Changes greater than ½ inch
Changes in level greater than ½ inch (12.7 mm) shall be made by means of a sloped surface not greater than 1 unit vertical in 20 units horizontal (5-percent slope), or a ramp, elevator or...
-
Accessible Sidewalks 3: Pedestrians with Low Vision
Requires the Registered User plan or above. Login! -
504.4 Tread Surface
Changes in level are not permitted. EXCEPTION: Treads shall be permitted to have a slope not steeper than 1:48. Advisory 504.4 Tread Surface....
-
504.4 Tread Surface
Changes in level are not permitted. EXCEPTION: Treads shall be permitted to have a slope not steeper than 1:48. Advisory 504.4 Tread Surface....
-
§ 38.83(c)(3) Ramp threshold
Changes in level between 1/4 inch and 1/2 inch shall be beveled with a slope no greater than 1:2....
-
§ 38.159(c)(3) Ramp threshold
Changes in level between 1/4 inch (6.5 mm) and 1/2 inch (13 mm) shall be beveled with a slope no greater than 1:2....
-
7.4.6 Tread Obstacles
Tread obstacles on trails shall not exceed 2 inches (50 mm) in height measured vertically to the highest point. Where the trail surface is paved or is elevated above the natural...
-
Wet Conditions [§405.10]
Wet Conditions [§405.10] Landings subject to wet conditions must be designed to prevent the accumulation of water. Landings are permitted slopes not steeper than 1:48 to allow for...
-
1131A.2 Changes greater than ½ inch
Changes in level greater than ½ inch (12.7 mm) shall be made by means of a sloped surface not greater than 1 unit vertical in 20 units horizontal (5-percent slope), or a ramp, elevator or...
-
504.4 Tread Surface
Changes in level are not permitted. EXCEPTION: Treads shall be permitted to have a slope not steeper than 1:48. Advisory 504.4 Tread Surface....
-
ElectionSource Wall Mounted Wireless Alert Assist
Wireless door bell attaches to wall and assists voters for entering voting precincts and entrances. 100 foot range.
-
407.4.8.2.2 Signal Level
407.4.8.2.2 Signal Level. The verbal annunciator shall be 10 dB minimum above ambient, but shall not exceed 80 dB, measured at the annunciator....
-
Existing Elevators (Alterations)
Alterations made to an existing car also must be made to each elevator programmed to respond to the same hall call so that a consistent level of accessibility within banks is maintained....
-
2.1.2.1 Summary of IEC 118‒4 (1981) Standards
2.1.2.1 Summary of IEC 118‒4 (1981) Standards With a source of 1000 Hz equal to the long-time average level of the speech signal applied to the input of the system, the resulting field...
-
ADA & Level Boarding - What constitutes an alteration?
49 CFR §§37.42(a); 37.3 DECEMBER 14, 2011
-
Contact Mat (BE9026)
When somebody steps on the Contact Mat, it triggers the connected Visit transmitter, and the transmitter sends signals to the Visit receiver to alert the user....
