The tops of picnic tables shall comply with 902.3.
Search Results "Signage Height"
Filters
Commonly Searched Documents
-
1011.4.1 Height
-
1011.4.1 Height
The tops of picnic tables shall comply with 902.3.
-
1002.6.2 Transfer Height
The height of transfer device seats shall be 14 inches (355 mm) minimum and 24 inches (610 mm) maximum measured from the load and unload surface....
-
1002.6.2 Transfer Height
The height of transfer device seats shall be 14 inches (355 mm) minimum and 24 inches (610 mm) maximum measured from the load and unload surface....
-
Effect of Handhelds on Transfer Height
Participant preference for grab bars and backrest heights for protocols B through E are shown in Table 17. For all protocols the tall grab bars were preferred....
-
11B-703.7.2.6.1 Men’s toilet and bathing facilities
Men’s toilet and bathing facilities shall be identified by an equilateral triangle, ¼ inch (6.4 mm) thick with edges 12 inches (305 mm) long and a vertex pointing upward. The...
-
11B-703.7.2.6.2 Women’s toilet and bathing facilities
Women’s toilet and bathing facilities shall be identified by a circle, ¼ inch (6.4 mm) thick and 12 inches (305 mm) in diameter. The circle symbol shall contrast with the door,...
-
11B-703.7.2.6.3 Unisex toilet and bathing facilities
Unisex toilet and bathing facilities shall be identified by a circle, ¼ inch (6.4 mm) thick and 12 inches (305 mm) in diameter with a ¼ inch (6.4 mm) thick triangle with a vertex...
-
Which Paths Lead to Usable Circulation Paths?
Any circulation paths that are not usable should include signs directing people to other, usable paths. People with limited mobility should be provided with written directions, a...
-
11B-703.7.2.6.4 Edges and corners
Edges of signs shall be rounded, chamfered or eased. Corners of signs shall have a minimum radius of 1/8 inch (3.2 mm).
-
11B-703.7.2.6.4 Edges and vertices on geometric symbols
11B-703.7.2.6.4 Edges and vertices on geometric symbols. Edges shall be eased or rounded at 1/16 inch (1.59 mm) minimum, or chamfered at 1/8 inch (3.2 mm) maximum. Vertices shall be...
-
11B-703.7.2.6.4 Edges and vertices on geometric symbols
Edges shall be eased or rounded at 1/16 inch (1.59 mm) minimum, or chamfered at 1/8 inch (3.2 mm) maximum. Vertices shall be radiused between 1/8 inch (3.2 mm) minimum and ¼ inch...
-
1023.9 Stairway identification signs
Section 1143A or Chapter 11B shall be located at the landing of each floor level, placed adjacent to the door on the latch side, in all enclosed stairways in buildings two or more stories in height...
-
(4) Adjustability: Method of Measurement
The MDE NPRM proposed that the measurement of the height of the transfer surface for both diagnostic equipment used in the supine, prone, or side-lying position and diagnostic equipment...
-
11B-502.6.2 Minimum fine
Additional language or an additional sign below the International Symbol of Accessibility shall state “Minimum Fine $250.”
-
11B-502.6.4 Marking
Each accessible car and van space shall have surface identification complying with either Section 11B-502.6.4.1 or 11B-502.6.4.2.
-
11B-502.6.2 Minimum fine
Additional language or an additional sign below the International Symbol of Accessibility shall state “Minimum Fine $250.”
-
11B-502.6.4 Marking
Each accessible car and van space shall have surface identification complying with either Section 11B-502.6.4.1 or 11B-502.6.4.2.
-
11B-502.6.2 Minimum fine
Additional language or an additional sign below the International Symbol of Accessibility shall state “Minimum Fine $250.”
-
11B-502.6.4 Marking
Each accessible car and van space shall have surface identification complying with either Section 11B-502.6.4.1 or 11B-502.6.4.2.
-
Height – M301.2.1 & M302.2.1
Height – M301.2.1 & M302.2.1 The subcommittee discussed the increments for adjustability and decided that infinite adjustability is the appropriate standard as both electronic and...
-
902.4.2 Height
The tops of tables and counters shall be 26 inches (660 mm) minimum and 30 inches (760 mm) maximum above the finish floor or ground.
-
902.4.2 Height
The tops of tables and counters shall be 26 inches (660 mm) minimum and 30 inches (760 mm) maximum above the finish floor or ground.
-
11B-216.8.1 Geometric symbols
Geometric symbols complying with Section 11B-703.7.2.6 shall be provided at entrances to toilet and bathing rooms. Exceptions: Geometric symbols shall not be required at...