shall not be required in assembly areas with 300 or fewer seats if the companion seats required by F221.3 and wheelchair spaces are located within the 2nd or 3rd quartile of the total row length...
Search Results "Segment Length"
Filters
Commonly Searched Documents
-
F221.2.3.1 Horizontal Dispersion
-
Construction Specification Institute
For longitudinal lines, measurements were to be taken in minimum 5 - foot lengths running parallel to the long dimension, with one measurement line per 3 feet of width and within 2 feet...
-
Large non-rail vehicle
Non-rail vehicles that are more than 25 feet (7.6 m) in length....
-
11B-705.1.2.3 Islands or cut-through medians
Exception: Detectable warnings shall be 24 inches (610 mm) minimum in depth at pedestrian islands or cut-through medians that are less than 96 inches (2438 mm) in length in the direction...
-
11B-812.6 Vehicle spaces
Exceptions: Where the long dimension of vehicle spaces is parallel to the traffic flow in the adjacent vehicular way, the length of vehicle spaces shall be 240 inches (6096 mm) minimum...
-
Small non-rail vehicle
Non-rail vehicles that are equal to or less than 25 feet (7.6 m) in length....
-
Feature 2 - Routes to the Building Entrance
An accessible route is at least 36 inches wide for the entire length of the route....
-
APPENDIX A
The committee discussed at length the different lifting systems used for adjustable height equipment and the viability of achieving the heights being considered....
-
Selection of Locations
The trail segments did not see high visitor use, and were restricted to just pedestrian access....
-
Slope and Rise [4.8.2]
Slope represents the proportion of vertical rise to horizontal length and can be represented as a ratio (as in ADAAG), percentage, pitch or in degrees....
-
M305.3.1.3 Vertical Position
The length of the gripping surface on vertical standing supports shall be 18 inches (455 mm) minimum....
-
11B-505.6 Gripping surface
Handrail gripping surfaces shall be continuous along their length and shall not be obstructed along their tops or sides....
-
1133A.4, Item 2
A minimum linear length of 30 inches (762 mm) of countertop shall be provided for a work surface....
-
1133A.4, Item 2
A minimum linear length of 30 inches (762 mm) of countertop shall be provided for a work surface....
-
11B-812.7.2 Marking
Access aisle markings may extend beyond the minimum required length....
-
Counters and Bars [5.2]
Types of Counters Maximum Height Minimum Length Knee Clearance (forward approach) Dining/Bars (service) 34 in 60 in required Dining/Bars...
-
Selection of Variables
Selection of Variables Our own review of the ADAAG requirements, plus that of our subcontractor KRW, reveals that the single most needed anthropometric datum, by far, is arm length....
-
T402.5 Surfaces
Ramp and bridgeplate surface material shall comply with T302 and extend across the full width and length of the ramp or bridgeplate....
-
1133A.4, Item 1
A minimum linear length of 30 inches (762 mm) of countertop shall be provided for the kitchen sink installation....
-
1133A.4, Item 1
A minimum linear length of 30 inches (762 mm) of countertop shall be provided for the kitchen sink installation....
-
Ronick Matting Systems BaseMat 300 Entrance Floor Mat
The entrance floor mats feature aluminum hinged framework with cushioned supports at the bottom of each segment....
-
11B-705.1.2.2.2.1 One entrance/exit point
Where the turning space has one entrance/exit point other than the sloped ramp segments, detectable warnings shall be 36 inches (914 mm) deep, as measured perpendicular to the curb, and...
-
Side Transfer Surface
A transfer surface located within the length of the examination surface that allows patient transfer on two opposing sides of the examination surface....
-
M305.2.1.1 End Transfer Supports
Transfer supports for transfer surfaces complying with M301.2.3.1 and M302.2 shall be located on the short side (length) opposite the transfer side....
