Cross slope is measured the same way as slope is measured (i.e., the rise over the run)....
Search Results "Measuring Instrument"
Filters
Commonly Searched Documents
-
405.3 Cross Slope
-
7.4.6 Tread Obstacles
Tread obstacles on trails shall not exceed 2 inches (50 mm) in height measured vertically to the highest point. ...
-
11B-604.7.1 Dispensers
Toilet paper dispensers shall comply with Section 11B-309.4 and shall be 7 inches (178 mm) minimum and 9 inches (229 mm) maximum in front of the water closet measured to the centerline of...
-
Definitions
that a polling place is compliant with the 2010 ADA Standards for Accessible Design (“2010 Standards”) on Election Day, whether such compliance is achieved through permanent architectural measures...
-
Road Roughness Analysis
The IRI also has an ASTM standard measurement protocol for consistent measurements....
-
810.2.2 Dimensions
Bus stop boarding and alighting areas shall provide a clear length of 96 inches (2440 mm) minimum, measured perpendicular to the curb or vehicle roadway edge, and a clear width of 60 inches...
-
10 - foot straightedge method
However, there is no standardized protocol to measure deviations in lengths less than ten feet. The same problem exists when measuring slope....
-
Effect on Removal of Barriers in Existing Facilities: ADA Standard Section 101.2
Section 101.2 of the ADA Standards covers the effects of the removal of barriers in existing facilities.
-
VII. Existing Facilities: Removal of Barriers
Examples of barrier removal measures include -- Installing ramps, Making curb cuts at sidewalks and entrances, Rearranging tables, chairs, vending machines, display...
-
1(2)(a)(i) Individual building test
It is impractical to provide an accessible entrance served by an accessible route when the terrain of the site is such that: (A) the slopes of the undisturbed site measured between the...
-
E. Staff Training
Subject Matter Experts and/or an outside source to all employees in the Elections Division and any relevant contractors or vendors, including those who conduct surveys or implement temporary measures...
-
Brewer Access™ High-Low Exam Table
leads the industry in innovation through our comprehensive line of power procedure tables, exam tables, seating, lighting, and broad line of durable medical equipment (IV poles, hampers, instrument...
-
11B-703.3.1 Dimensions and capitalization
TABLE 11B-703.3.1 BRAILLE DIMENSIONS MEASUREMENT RANGE MINIMUM IN INCHES MAXIMUM IN INCHES Dot base diameter...
-
11B-809.12 Electrical receptacles, controls and switches
circuits of 30 amperes or less, communication system receptacles, controls and switches shall be located as follows: Where there is no obstruction, 48 inches (1219 mm) maximum measured...
-
C. Who should conduct the survey?
For example, one surveyor can take notes and complete forms while another surveyor is obtaining measurements and taking photos....
-
Recessed Doors and Gates: ADA Standard Section 404.2.4.3
Section 404.2.4.3 covers the current ADA Standards for maneuvering clearances at recessed doors and gates.
-
Dispensers: ADA Standard Section 604.9.6
Section 604.9.5 covers the current ADA Standards for dispensers in children's use toilet compartments.
-
11B-804.2 Clearance
Clearances are measured from the furthest projecting face of all opposing base cabinets, counter tops, appliances, or walls, excluding hardware. ◼...
-
§382.21(c)
(c) If a passenger with a communicable disease meeting the direct threat criteria of this section gives you a medical certificate of the kind outlined in §382.23(c)(2) describing measures...
-
810.2.2 Dimensions
Bus stop boarding and alighting areas shall provide a clear length of 96 inches (2440 mm) minimum, measured perpendicular to the curb or vehicle roadway edge, and a clear width of 60 inches...
-
407.2.1.1 Height
Call buttons and keypads shall be located within one of the reach ranges specified in 308, measured to the centerline of the highest operable part....
-
407.2.1.1 Height
Call buttons and keypads shall be located within one of the reach ranges specified in 308, measured to the centerline of the highest operable part....
-
4.34.6.4(1)
(1) The counter shall be mounted at a maximum height of 34 in (865 mm) above the floor, measured from the floor to the top of the counter surface, or shall be adjustable or replaceable as...
-
11B-604.3.1 Size
Clearance around a water closet shall be 60 inches (1524 mm) minimum measured perpendicular from the side wall and 56 inches (1422 mm) minimum measured perpendicular from the rear wall....
