The Board has removed the minimum surface requirement (2 square feet) for vanity counter tops....
Search Results "Minimum Dimension"
-
Vanity Counter Tops
-
Curb Ramps at Marked Crossings and Vehicular Lanes
The detectable warning shall extend the full width of the curb ramp (exclusive of flared sides) and shall extend either the full depth of the curb ramp or 24 inches (610 mm) deep minimum...
-
Doors, Doorways, and Gates
In the final rule, clarification has been added in 206.5.3 that the 32 inch minimum clearance applies to those doors "providing user passage" into and within guest rooms not required to...
-
3. Modified Theaters
The modifications listed here are minimum modifications mandated under this Consent Order and to the extent that actual modifications include and exceed those listed here, they will be deemed...
-
11B-407.2.3.1 Floor designation
Tactile characters shall be 2 inches (51 mm) high minimum. A tactile star shall be provided on both jambs at the main entry level....
-
3. Buttock-Popliteal Length
The horizontal line splitting the box depicts the median, the box length represents the inter-quartile (25th – 75th percentile) range, and the whiskers represent the minimum and maximum...
-
What other voting rights laws does the Justice Department enforce?
The Help America Vote Act of 2002 (42 U.S.C. 15301 to 15545) is designed to improve the administration of elections in the United States by establishing minimum standards for states to follow...
-
404.2.10 Door and Gate Surfaces
Tempered glass doors without stiles and having a bottom rail or shoe with the top leading edge tapered at 60 degrees minimum from the horizontal shall not be required to meet the 10 inch...
-
5.1.2 Transfer Surface High Height Recommendations for M301 and M302
Since one key factor in ease of transfer is locating the transfer surface near or at the same height as the seat of the wheeled mobility device, moving the minimum high point for adjustability...
-
6. Transfer Surface Height
For many types of imaging equipment it will not be feasible to provide a transfer surface meeting the considered minimum height whether it is17, 18, or 19 inches....
-
Front grab bar protocol
Maximum and minimum heights attainable, front grab use, and grab bar heights for each the lower-height and higher-height transfers were recorded....
-
711.3.2 Membrane penetrations
Where walls and partitions are required to have a minimum 1-hour fire-resistance rating, recessed fixtures shall be installed such that the required fire resistance will not be reduced....
-
404.2.10 Door and Gate Surfaces
Tempered glass doors without stiles and having a bottom rail or shoe with the top leading edge tapered at 60 degrees minimum from the horizontal shall not be required to meet the 10 inch...
-
233.3.4.2 Alterations to Individual Residential Dwelling Units
least one other room is altered, the requirements of 233.3.1 shall apply to the altered residential dwelling units until the total number of residential dwelling units complies with the minimum...
-
Public Education
The Supervisor shall ensure that the information on the accessible voting system on its website conforms to, at a minimum, the Web Content Accessibility Guidelines 2.0 Level AA Success Criteria...
-
7.3(1)
(1) In new construction, accessible check-out aisles shall be provided in conformance with the table below: Total Check-out Aisles of Each Design Minimum Number...
-
Carpet [4.5.3]
There should be minimum movement, none if possible, between the cushion or pad and the carpet....
-
§1630.2(j)(3)(iii)
iii) For example, applying the principles set forth in paragraphs (j)(1)(i) through (ix) of this section, it should easily be concluded that the following types of impairments will, at a minimum...
-
11B-233.3.4.2 Alterations to individual residential dwelling units
other room is altered, the requirements of Section 11B-233.3.1 shall apply to the altered residential dwelling units until the total number of residential dwelling units complies with the minimum...
-
TownSteel FME4030 Mortise Lockdown Rigid Trim Security Cylinder
User/Office keycards per Lock: 250 Capacity of Remote Control Unit (RCU) per Lock: 120 Credential verification time: Less than 0.5 second Keycard maximum read/write distance: ¾” RCU minimum...
-
TownSteel FME4020 Mortise Lockdown Clutched Trim
User/Office keycards per Lock: 250 Capacity of Remote Control Unit (RCU) per Lock: 120 Credential verification time: Less than 0.5 second Keycard maximum read/write distance: ¾” RCU minimum...
-
TownSteel FME4010 Mortise Lockdown Rigid Trim RFID Mortise
User/Office keycards per Lock: 250 Capacity of Remote Control Unit (RCU) per Lock: 120 Credential verification time: Less than 0.5 second Keycard maximum read/write distance: ¾” RCU minimum...
-
Diaper Deck Infant Changing Table
Under no circumstances should the Diaper DeckTM be mounted on a wall not able to withstand minimum of 100 lbs. per sq. ft. in all directions....
-
TownSteel FCE4030 Cylindrical Lockdown Rigid Trim Security Cylinder RFID Cylindrical
User/Office keycards per Lock: 250 Capacity of Remote Control Unit (RCU) per Lock: 120 Credential verification time: Less than 0.5 second Keycard maximum read/write distance: ¾” RCU minimum...
