Written interpretations and guidance shall be developed through the Department's coordinating mechanism for disability matters, the Disability Law Coordinating Council....
Search Results "Subject Matter Expert"
-
§ 37.15 Interpretations and guidance
-
General: ADA Standard Section 233.1
Section 233 of the ADA Standards covers information in the current ADA Standards on scoping requirements for residential facilities.
-
11B-224.7.2 Multi-bedroom housing units with adaptable features
Housing at a place of education that is subject to this part shall comply with the provisions of the 2010 Standards applicable to transient lodging, including, but not limited to, the requirements...
-
E. IMPLEMENTATION AND ENFORCEMENT
with this Agreement or any requirements contained herein, the United States agrees to notify the Museum in writing of the alleged noncompliance and attempt to seek a resolution of the matter...
-
The Basis for the 2010 ADA Standards Pocket Guide
Learn the basis of the 2010 ADA Standards Pocket Guide
-
Alterations to Vacated Buildings: ADA Standard Section 233.3.4.1
Section 233.3.4.1 covers scoping requirements in the current ADA Standards for alterations to vacated buildings.
-
1.9.1.1 Application
to a state, county, municipality or other political subdivision of the state, the entity that collects and controls the distribution of the public funds becomes the funding source, and subject...
-
1.9.1.1 Application
to a state, county, municipality or other political subdivision of the state, the entity that collects and controls the distribution of the public funds becomes the funding source, and subject...
-
Q1.) When a ramp has a maximum slope of 1:12 or 8.33%, is that considered a range of from 0% to 8.33% which would allow no slope greater than 8.33% or is that a simple maximum which would allow a tolerance above 8.33%? Similarly, is a cabinet countertop that can be no higher than 34” AFF a range of from 0” to 34” AFF with no additional height allowed, or is a tolerance allowed for variations in the floor surface or cabinet construction?
The consistent technical assistance on this question has been that both are subject to tolerances....
-
Sec. 469.107(1)
(1) review plans and specifications and make inspections of a structure not otherwise subject to this chapter; and...
-
§27.7(b)(4)(i)
(i) That have the effect of subjecting qualified persons with a disability to discrimination on the basis of disability,...
-
§104.4(b)(4)(i)
(i) that have the effect of subjecting qualified handicapped persons to discrimination on the basis of handicap,...
-
§35.130(b)(3)(i)
(i) That have the effect of subjecting qualified individuals with disabilities to discrimination on the basis of disability;...
-
E101.3 Conventional Industry Tolerances
Dimensions are subject to conventional industry tolerances except where dimensions are stated as a range....
-
C101.3 Conventional Industry Tolerances
Dimensions are subject to conventional industry tolerances except where dimensions are stated as a range....
-
§ 35.130(b)(3)(i)
(i) That have the effect of subjecting qualified individuals with disabilities to discrimination on the basis of disability;...
-
T215 Communication Features
(Section T702, in turn, addresses such matters as character style and height, line spacing, and contrast.) See 2010 NPRM, Sections T203.10.2, T702....
-
12188(a)(1) Availability of remedies and procedures
remedies and procedures The remedies and procedures set forth in section 2000a-3(a) of this title are the remedies and procedures this subchapter provides to any person who is being subjected...
-
§ 37.33(a)
Transportation systems operated by public airport operators, which provide designated public transportation and connect parking lots and terminals or provide transportation among terminals, are subject...
-
406.8 Detectable Warnings
Curb ramps subject to Department of Transportation regulation 49 CFR 37.21 shall have a detectable warning complying with 705....
-
A. Background
This matter was initiated by a complaint filed with the United States Department of Justice (the “Department”) against Jefferson Outpatient under Title III of the Americans with Disabilities...
-
M101.6 Dimensional Tolerances
Dimensions are subject to conventional industry tolerances for manufacturing processes, material properties, and field conditions....
-
504.7 Wet Conditions
Stair treads and landings subject to wet conditions shall be designed to prevent the accumulation of water....
-
225(e)(1) In general
(1) In general Subject to subsections (f) and (g) of this section, the Commission shall enforce this section....