(ii) that perpetuate the discrimination of others who are subject to common administrative control....
Search Results "Subject Matter Expert"
Commonly Searched Documents
- 
    
  
  12182(b)(1)(D)(ii)
  
 - 
    
  
  3.2 Dimensional Tolerances
  
All dimensions are subject to conventional building industry tolerances for field conditions....
 - 
    
  
  3.2 DIMENSIONAL TOLERANCES
  
All dimensions are subject to conventional building industry tolerances for field conditions....
 - 
    
  
  405.10 Wet Conditions
  
Landings subject to wet conditions shall be designed to prevent the accumulation of water....
 - 
    
  
  Enforcing Authority
  
An agency that adopts the standards as mandatory requirements for entities subject to its jurisdiction....
 - 
    
  
  §1630.7(b)
  
(b) That perpetuate the discrimination of others who are subject to common administrative control....
 - 
    
  
  11B-405.10 Wet conditions
  
Landings subject to wet conditions shall be designed to prevent the accumulation of water....
 - 
    
  
  11B-405.10 Wet conditions
  
Landings subject to wet conditions shall be designed to prevent the accumulation of water....
 - 
    
  
  III-1.7000 Relationship to title II
  
As a public accommodation, X Corporation is subject to title III of the ADA. The State department of parks, a public entity, is subject to title II....
 - 
    
  
  12188(a)(1) Availability of remedies and procedures
  
remedies and procedures The remedies and procedures set forth in section 2000a-3(a) of this title are the remedies and procedures this subchapter provides to any person who is being subjected...
 - 
    
  
  406.8 Detectable Warnings
  
Curb ramps subject to Department of Transportation regulation 49 CFR 37.21 shall have a detectable warning complying with 705....
 - 
    
  
  § 37.33(a)
  
Transportation systems operated by public airport operators, which provide designated public transportation and connect parking lots and terminals or provide transportation among terminals, are subject...
 - 
    
  
  5. Conditions Precedent
  
(h) The Pineda Action has been dismissed with prejudice, and the Pineda Plaintiffs have provided the City with a general release of claims arising from or related to the matters alleged...
 - 
    
  
  UNITED STATES OF AMERICA v. METROPOLITAN TRANSPORTATION AUTHORITY and NEW YORK CITY TRANSIT AUTHORITY - OPINION & ORDER
  
The distinction matters because under § 37.43(a)(1), Defendants must make certain alterations to increase accessibility no matter the cost, while under § 37.43(a)(2), Defendants must make...
 - 
    
  
  INVESTIGATION AND FINDINGS
  
Part 36, Subpart E, to investigate the allegations of the complaint in this matter to determine AFAC’s compliance with title III of the ADA. The U.S....
 - 
    
  
  Q1.) When a ramp has a maximum slope of 1:12 or 8.33%, is that considered a range of from 0% to 8.33% which would allow no slope greater than 8.33% or is that a simple maximum which would allow a tolerance above 8.33%?  Similarly, is a cabinet countertop that can be no higher than 34” AFF a range of from 0” to 34” AFF with no additional height allowed, or is a tolerance allowed for variations in the floor surface or cabinet construction?
  
The consistent technical assistance on this question has been that both are subject to tolerances....
 - 
    
  
  Sec. 469.107(1)
  
(1) review plans and specifications and make inspections of a structure not otherwise subject to this chapter; and...
 - 
    
  
  §27.7(b)(4)(i)
  
(i) That have the effect of subjecting qualified persons with a disability to discrimination on the basis of disability,...
 - 
    
  
  §104.4(b)(4)(i)
  
(i) that have the effect of subjecting qualified handicapped persons to discrimination on the basis of handicap,...
 - 
    
  
  §35.130(b)(3)(i)
  
(i) That have the effect of subjecting qualified individuals with disabilities to discrimination on the basis of disability;...
 - 
    
  
  E101.3 Conventional Industry Tolerances
  
Dimensions are subject to conventional industry tolerances except where dimensions are stated as a range....
 - 
    
  
  C101.3 Conventional Industry Tolerances
  
Dimensions are subject to conventional industry tolerances except where dimensions are stated as a range....
 - 
    
  
  § 35.130(b)(3)(i)
  
(i) That have the effect of subjecting qualified individuals with disabilities to discrimination on the basis of disability;...
 - 
    
  
  §27.19(a)
  
(a) Recipients subject to this part (whether public or private entities as defined in 49 CFR part 37) shall comply with all applicable requirements of the Americans with Disabilities Act...