Drive-up EVCS shall not be required to be identified by an ISA.
Search Results "Vehicle Hand Control"
Filters
Commonly Searched Documents
-
11B-812.8.5 Drive-up
-
11B-812.10.3 Point-of-sale devices
Where provided, point-of-sale devices shall comply with Sections 11B-707.2, 11B-707.3, 11B-707.7.2, and 11B-707.9.
-
11B-407.4.7.1.1 Type
Control buttons shall be identified by raised characters or symbols, white on a black background, complying with Section 11B-703.2 and Braille complying with Section 11B-703.3....
-
11B-407.4.7.1.3 Symbols
The control button for the emergency stop, alarm, door open, door close, main entry floor, and phone, shall be identified with raised symbols and Braille as shown in Table 11B-407.4.7.1.3...
-
503.4.2 Audio Description Controls
Where user controls are provided for program selection, ICT shall provide user controls for the selection of audio descriptions at the same menu level as the user controls for volume or...
-
503.4.2 Audio Description Controls
Where user controls are provided for program selection, ICT shall provide user controls for the selection of audio description at the same menu level as the user controls for volume or program...
-
Volume Controls
Does the accessible phone have volume controls? Yes __ No __ N/A __ Comments: ___________________________________________ c....
-
Looking at Cal Green 5.106.5.3, we must provide the conduits and panel capacity for future installation for the required number of spaces (2 in this case). However, it is only when the equipment is to be installed that we need to refer to CBC and CEC. Section 11B-228.3.1 also reiterates this. Therefore, we would show the location of the conduit stub outs adjacent to 2 current parking spaces and would show space on the electric panel for the future equipment – and that is all. At this time, we do not need to show the requirements for EV accessibility when equipment is installed per Chapter 11B. Is my interpretation correct?
RESPONSE: CBC Chapter 11B accessibility provisions for EVCS apply when a project consists of one or more electric vehicle charging spaces served by an electric vehicle charger or other charging...
-
T704 Announcement Systems
First, rear-facing wheelchair spaces are not required by the 2016 Non-Rail Vehicle Guidelines....
-
§ 38.23(c)(5) Slope
If the height of the vehicle floor from which the ramp is deployed is 3 inches or less above a 6-inch curb, a maximum slope of 1:4 is permitted; if the height of the vehicle floor from which...
-
413.1.2 Audio Description Controls
ICT shall provide user controls for the selection of audio description in at least one location that is comparable in prominence to the location of the user controls for program selection...
-
Operable Parts: ADA Standard Section 410.5
Section 410.5 covers the current ADA Standards for operable parts of the platform lift controls.
-
DRIVE-UP ELECTRIC VEHICLE CHARGING STATION
An electric vehicle charging station in which use is limited to 30 minutes maximum and is provided at a location where the electric vehicle approaches in the forward direction, stops in...
-
DRIVE-UP ELECTRIC VEHICLE CHARGING STATION
An electric vehicle charging station in which use is limited to 30 minutes maximum and is provided at a location where the electric vehicle approaches in the forward direction, stops in...
-
11B-410.5 Operable parts
Controls for platform lifts shall comply with Section 11B-309....
-
Operable Parts: ADA Standard Section 205
Section 205 covers scoping requirements for operable parts in the most current ADA Standards.
-
General: ADA Standard Section 309.1
Section 309.1 of the ADA Standards covers information in the current ADA Standards for reach ranges for operable parts.
-
Operable Parts: ADA Standard Section 309
Section 309 covers the current ADA Standards for reach ranges for operable parts.
-
11B-205 Operable parts
[See subsections ...]
-
11B-309 Operable parts
[See subsections ...]
-
11B-411.4.7.4 Button spacing
Button spacing shall comply with Section 11B-407.4.7.1.5.
-
11B-309.1 General
Operable parts shall comply with Section 11B-309.
-
11B-407.4.6.2.1 Size and shape
11B-407.4.6.2.1 Size and shape. Buttons shall have square shoulders, be ¾ inch (19.1 mm) minimum in their smallest dimension and be raised 1/8 inch (3.2 mm) plus or minus 1/32 inch...
-
11B-407.4.6.2.2 Arrangement
Buttons shall be arranged with numbers in ascending order. When two or more columns of buttons are provided they shall read from left to right.