Tactile characters on signs shall be located 48 inches (1219 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest Braille cells and 60 inches (1524...
Search Results "Tape Measure"
Filters
Commonly Searched Documents
-
11B-703.4.1 Height above finish floor or ground
-
Grievance Procedure under The Americans with Disabilities Act
Alternative means of filing complaints, such as personal interviews or a tape recording of the complaint, will be made available for persons with disabilities upon request....
-
2. Different Types of Auxiliary Aids and Services
of written notes TTY or video relay service email text messaging instant messaging qualified readers assistance filling out forms taped...
-
Tax Credits and Deductions
The tax credit can be used to offset the cost of undertaking barrier removal and alterations to improve accessibility; providing accessible formats such as Braille, large print and audio tape...
-
Access-Able Designs Stationary Dressing Bench DST-101
Measures 48"W x 24"D back measures 48”W x 24”H (custom sizes available) 5 year warranty....
-
BS8300:2001 Research
It is also not clear what was measured if the chair had no armrests or slanted armrests....
-
§ 36.304(c)(1)
(1) First, a public accommodation should take measures to provide access to a place of public accommodation from public sidewalks, parking, or public transportation....
-
Sec.36.304(c)(1)
(1) First, a public accommodation should take measures to provide access to a place of public accommodation from public sidewalks, parking, or public transportation....
-
405.3 Cross Slope
Cross slope is measured the same way as slope is measured (i.e., the rise over the run)....
-
810.2.2 Dimensions
Bus stop boarding and alighting areas shall provide a clear length of 96 inches (2440 mm) minimum, measured perpendicular to the curb or vehicle roadway edge, and a clear width of 60 inches...
-
405.3 Cross Slope
Cross slope is measured the same way as slope is measured (i.e., the rise over the run)....
-
R308.1.1.1 Dimensions
Boarding and alighting areas shall provide a clear length of 2.4 m (8.0 ft) minimum, measured perpendicular to the curb or street or highway edge, and a clear width of 1.5 m (5.0 ft) minimum...
-
Future Work
The devices that are on the market to measure roadway roughness are not applicable to sidewalk and pedestrian surfaces because they either use accelerometers to measure the surface profile...
-
11B-810.2.2 Dimensions
Bus stop boarding and alighting areas shall provide a clear length of 96 inches (2438 mm) minimum, measured perpendicular to the curb or vehicle roadway edge, and a clear width of 60 inches...
-
11B-703.4.1 Height above finish floor or ground
Tactile characters on signs shall be located 48 inches (1219 mm) minimum above the finish floor or ground surface, measured from the baseline of the lowest Braille cells and 60 inches (1524...
-
608.2.1 Transfer Type Shower Compartments
Transfer type shower compartments shall be 36 inches (915 mm) by 36 inches (915 mm) clear inside dimensions measured at the center points of opposing sides and shall have a 36 inch (915...
-
Definitions
that a polling place is compliant with the 2010 ADA Standards for Accessible Design (“2010 Standards”) on Election Day, whether such compliance is achieved through permanent architectural measures...
-
Sec.36.304(c)(3)
(3) Third, a public accommodation should take measures to provide access to restroom facilities....
-
§ 36.304(c)(3)
(3) Third, a public accommodation should take measures to provide access to restroom facilities....
-
Background
Further, industry standards, specifications, and measurement procedures do not even address some measures important to facility usability in new construction, such as how to measure the...
-
604.3.1 Size
Clearance around a water closet shall be 60 inches (1525 mm) minimum measured perpendicular from the side wall and 56 inches (1420 mm) minimum measured perpendicular from the rear wall....
-
1.2.1 Walks and other non - ramp surfaces
When overall running slope for walks is measured according to Section 1.1.3 a recommended tolerance for running slope is +1%....
-
§ 37.151(a)(2)
(2) The entity determines that it cannot make measured progress toward compliance in any year before full compliance is required....
