Section 404.2.7 also covers the operating characteristics and height of door and gate hardware....
Search Results "Shower Door"
Filters
Commonly Searched Documents
-
Door and Gate Hardware
-
4.13.9* DOOR HARDWARE
When sliding doors are fully open, operating hardware shall be exposed and usable from both sides....
-
608.2.3 Alternate Roll-In Type Shower Compartments
Alternate roll-in type shower compartments shall be 36 inches (915 mm) wide and 60 inches (1525 mm) deep minimum clear inside dimensions measured at center points of opposing sides....
-
11B-604.8.2.2 Doors
Toilet compartment doors, including door hardware, shall comply with Section 11B-404, except that if the approach is to the latch side of the compartment door, clearance between the door...
-
11B-604.8.1.2 Doors
11B-604.8.1.2 Doors....
-
11B-604.8.1.2 Doors
Toilet compartment doors, including door hardware, shall comply with Section 11B-404 except that if the approach is from the push side of the compartment door, clearance between the door...
-
11B-604.8.1.2 Doors
Toilet compartment doors, including door hardware, shall comply with Section 11B-404 except that if the approach is from the push side of the compartment door, clearance between the door...
-
Verify Framing
Slope, width and headroom of all interior accessible routes. 11B-402 Door opening widths. 11B-404 Maneuvering clearances...
-
Verify Framing
Slope, width and headroom of all interior accessible routes. 11B-402 Door opening widths. 11B-404 Maneuvering clearances...
-
11B-404.2.8.1 Door closers and gate closers
Door closers and gate closers shall be adjusted so that from an open position of 90 degrees, the time required to move the door to a position of 12 degrees from the latch is 5 seconds minimum...
-
11B-404.2.8.1 Door closers and gate closers
Door closers and gate closers shall be adjusted so that from an open position of 90 degrees, the time required to move the door to a position of 12 degrees from the latch is 5 seconds minimum...
-
11B-411.3.5 Width
The width of elevator doors shall comply with Table 11B-407.4.1....
-
608 Shower Compartments
[See subsections ...]
-
608 Shower Compartments
[See subsections ...]
-
ROLL-IN SHOWER STALLS
[See subsections ...]
-
4.21 Shower Stalls
[See subsections ...]
-
A4.21 Shower Stalls
[See subsections ...]
-
608 Shower Compartments
[See subsections ...]
-
A4.21 SHOWER STALLS
[See subsections ...]
-
Doors in a Series
A few commenters expressed concern that the Guidelines did not provide design for an entrance that consists of a series of more than one door....
-
11B-404.2.8.1 Door closers and gate closers
Door closers and gate closers shall be adjusted so that from an open position of 90 degrees, the time required to move the door to a position of 12 degrees from the latch is 5 seconds minimum...
-
2a
Do large showers measure at least 30" wide by 60" deep as shown in Figure 35(b) below?...
-
1991 / 1994 ADA Standards - Plan Review Tool - Doors
1991 / 1994 ADA Standards - Plan Review Tool - Doors Click here to view/download the pdf, Page 1 of 2 (256 KB) Click here to view/download the pdf, Page 2 of 2 (272 KB) * * * *...
-
Is compliance on both sides of a door or gate required when it is usable only from one side?
No, compliance is not required on both sides of those doors or gates that can be used in one direction only. Compliance is required only on the usable side....