ADA Actuators – 4.75” Square with Text Only Application: - For use with ADA low energy power operators - Employs capacitance technology similar to star devices to operate...
Search Results "Push Side"
-
Hager Companies 4.75” Square ADA Actuator 2-659-0308
-
Hager Companies 6” Round ADA Actuator 2-659-0303
ADA Actuators - 6" Round with Text and ISA Logo Application: - For use with ADA low energy power operators - Employs capacitance technology similar to star devices to...
-
Heavy Duty Telephone Manual Dialing with Keypad
Heavy Duty Telephone Manual Dialing with Keypad Model Number: 2300-675 Dimensions: 10” H x 4” W x 4” D Telephone line powered, no external power source needed Perfect for...
-
Allen Tel ADA Outdoor Phones for Hearing Impaired Single Number Dial
ADA compliant outdoor phone with amplified receiver and single number dialer. No housing. Handset with 29 inch armored cord and amplified receiver Braille labeling and ID...
-
Bobrick Two-Wall Toilet Compartment Grab Bar B-5897
42" W x 54" D (107 x 137cm), 1-1/4" (32mm) dia. Constructed of 18-gauge (1.2mm), type 304 satin-finish stainless steel tubing. Concealed mounting flange 1/8" (3mm) thick, type 304...
-
Bobrick Two-Wall Toilet Compartment Grab Bar B-6897
42" W x 54" D (107 x 137cm), 1-1/2" (38mm) dia. Constructed of 18-gauge (1.2mm), type 304 satin-finish stainless steel tubing. Concealed mounting flange 1/8" (3mm) thick, type 304...
-
Bobrick Two-Wall Toilet Compartment Grab Bar Peened B-5897.99
42" W x 54" D (107 x 137cm), 1-1/4" (32mm) dia., peened finish. Constructed of 18-gauge (1.2mm), type 304 satin-finish stainless steel tubing. Concealed mounting flange 1/8" (3mm)...
-
Bobrick Two-Wall Toilet Compartment Grab Bar Peened B-6897.99
42" W x 54" D (107 x 137cm), 1-1/2" (38mm) dia., peened finish. Constructed of 18-gauge (1.2mm), type 304 satin-finish stainless steel tubing. Concealed mounting flange 1/8" (3mm)...
-
1. Transfer Surface
[See subsections ...]
-
4.34.3(2)(b) Reach Depth More Than 10 in
(b) Reach Depth More Than 10 in (255 mm). Where the reach depth to the operable parts of any control as measured from the vertical plane perpendicular to the edge of the unobstructed...
-
4.34.3(2)(a) Reach Depth Not More Than 10 in
(a) Reach Depth Not More Than 10 in (255 mm). Where the reach depth to the operable parts of all controls as measured from the vertical plane perpendicular to the edge of the...
-
A4.27.3 HEIGHT
Fig. A6 further illustrates mandatory and advisory control mounting height provision for typical equipment. Note distinction between built-in equipment (considered real property) and...
-
Transfer Surface Height (M301.2.1 and M302.2.1)
For many patients who use mobility devices, independent transfer is possible only if the height of the transfer surface is at or near the seat height of their mobility device. The...
-
5.4.9 Interruptions Along Transfer Support Gripping for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
5.4.9 Interruptions Along Transfer Support Gripping for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position....
-
M102.1 Defined Terms (Section-by-Section Analysis)
However, the Access Board has decided to add six additional terms to this section; end transfer surface, examination chair, imagining [sic] equipment with bores, imagining [sic] bed, side...
-
Clarity Ensemble Amplified Captioned Telephone
with fonts that can be enlarged with the swipe of a finger Large, easy-to-read fonts and adjustable contrast ClarityLogicTM remote diagnostic service programs your phone with the push...
-
M301.3.1 Transfer Supports
A) For transfer depths less than or equal to 24 inches a transfer support will be located opposite the transfer side....
-
5.4.3 Transfer Support Height for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
5.4.3 Transfer Support Height for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position....
-
5.4.7 Transfer Support Gripping Surface Clearance for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
5.4.7 Transfer Support Gripping Surface Clearance for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position....
-
5.4.6 Transfer Support Gripping Surface Cross Section for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
5.4.6 Transfer Support Gripping Surface Cross Section for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position....
-
Section D: Entrances
(§§309.4, 404.2.7) D3 On the pull side of the door, is there at least 18" of clearance provided to the side of the latch?...
-
Figure 308.3.2 Obstructed High Side Reach – Drawing from the U.S. Access Board
-
5.4.4 Transfer Support Distance From Transfer Surface for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position
5.4.4 Transfer Support Distance From Transfer Surface for Equipment Used in a Supine, Prone, Side-Lying, or Seated Position....
