2. A minimum linear length of 30 inches (762 mm) of countertop shall be provided for a work surface.
Search Results "Counter Depth"
Filters
Commonly Searched Documents
-
1133A.4, Item 2
-
1133A.4.1 Repositionable countertops
Repositionable countertops shall be provided in a minimum of 5 percent of the covered multifamily dwelling units. Repositionable countertops shall comply with the following:
-
7.3(1)
(1) In new construction, accessible check-out aisles shall be provided in conformance with the table below: Total Check-out Aisles of Each Design Minimum...
-
1133A.4.1 Repositionable countertops
Repositionable countertops shall be provided in a minimum of 5 percent of the covered multifamily dwelling units. Repositionable countertops shall comply with the following:
-
1133A.4, Item 2
2. A minimum linear length of 30 inches (762 mm) of countertop shall be provided for a work surface.
-
1133A.4.1 Repositionable countertops
Repositionable countertops shall be provided in a minimum of 5 percent of the covered multifamily dwelling units. Repositionable countertops shall comply with the...
-
Reach Ranges and Operability Requirements
Obstructed Forward Reach—When an object must be reached over an obstruction, the clear floor space must extend beneath the obstruction for at least as far as the reach depth over the obstruction...
-
1133A.4.1, Item 2
Base cabinets directly under the kitchen sink counter area and work surface shall be removable as required in Section 1133A.3....
-
904.6 Security Glazing
Where counters or teller windows have security glazing to separate personnel from the public, a method to facilitate voice communication shall be provided....
-
904.6 Security Glazing
Where counters or teller windows have security glazing to separate personnel from the public, a method to facilitate voice communication shall be provided....
-
904.6 Security Glazing
Where counters or teller windows have security glazing to separate personnel from the public, a method to facilitate voice communication shall be provided....
-
11B-904.6 Security glazing
Where counters or teller windows have security glazing to separate personnel from the public, a method to facilitate voice communication shall be provided....
-
11B-904.6 Security glazing
Where counters or teller windows have security glazing to separate personnel from the public, a method to facilitate voice communication shall be provided....
-
Side reach (Section-by-Section Analysis)
The cost of lowering counter height, in combination with the lack of control businesses exercise over certain prefabricated service or vending fixtures, outweighed, they argued, any benefits...
-
Side reach (Section-by-Section Analysis)
The cost of lowering counter height, in combination with the lack of control businesses exercise over certain prefabricated service or vending fixtures, outweighed, they argued, any benefits...
-
11B-904.6 Security glazing
Where counters or teller windows have security glazing to separate personnel from the public, a method to facilitate voice communication shall be provided....
-
4.2.5* Forward Reach
If the clear floor space only allows forward approach to an object, the maximum high forward reach allowed shall be 48 in (1220 mm) (see Fig. 5(a)). The minimum low forward reach is...
-
4.2.6* Side Reach
If the clear floor space allows parallel approach by a person in a wheelchair, the maximum high side reach allowed shall be 54 in (1370 mm) and the low side reach shall be no less...
-
4.2.5 FORWARD REACH
If the clear floor space only allows forward approach to an object, the maximum high forward reach allowed shall be 48 in (1220 mm) (see Fig. 5(a)). The minimum low forward reach is...
-
4.2.6* SIDE REACH
If the clear floor space allows parallel approach by a person in a wheelchair, the maximum high side reach allowed shall be 54 in (1370 mm) and the low side reach shall be no less...
-
Knee and Toe Clearances
[See subsections ...]
-
Treads and Riser Specifications in the ADA Standards (§504)
Treads and Riser Specifications in the ADA Standards (§504) Nosing Specifications
-
1133A.4, Item 3
3. Sinks and work surfaces may be a single integral unit a minimum of 60 inches (1524 mm) in length, or be separate components. Exception: Two 15-inch (381 mm) wide minimum...